Airtac 3V-F Base 3V300M8F
The AirTAC Airtac 3V-F Base 3V300M8F is a genuine 3V-F manifold base manifold base for 8 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations8
- Series3V-F manifold base
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac 3V-F Base 3V300M8F
Planning a panel with eight separate 3/2 switching points? The 3V300M8F replaces eight independently plumbed valves with one machined block: eight stations, one air inlet, one common supply. Each mounted valve keeps its own outlet, exhaust and electrical control.
The base itself is unpowered - no coil, no voltage, no state - because those properties sit in the valves you order separately. It is a genuine AirTAC part, and the family behind it spans both NC and NO valves, five coil voltages and two electrical entries.
Airtac 3V-F Base 3V300M8F Technical Specifications
| Model | Airtac 3V-F Base 3V300M8F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 8 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: Airtac 3V-F Base 3V300M8F
| 3V-F manifold base | Body. |
|---|---|
| 8F | 8 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V-F Base 3V300M8F Is Used
Laboratory automation switching
Drive the small air functions of a lab analyser - wash, purge, clamp - from one manifold inside the instrument cabinet.
Palletiser gripper stations
Mount the suction and release valves of a palletising head on one block carried at the end of the arm.
Maintenance workshop bench
Keep a set of blow-off and clamping valves on a shared manifold for jig set-up and repair work.
Is the Airtac 3V-F Base 3V300M8F the Right Part?
Work out one valve per function - a single-acting cylinder, an air blow-off, a suction cup line - then give each its own state, port size and coil voltage and order them separately. Port sizes across the family run from M5 up to 3/8 inch, so match the step to the actuator: a 3/8 inch port suits a larger single-acting cylinder than a 1/8 inch one. Because flow figures for this family are not published by us, ask us to confirm sizing before you commit; if you want a valve whose figures are on the page today, the AirTAC 3V2 and 3V3 bodies are documented. A double-acting cylinder is a 4V job, not a 3/2 one.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V-F Base 3V300M8F FAQ
Whatever the AirTAC datasheet carries for the base and for the valves you mount on it - send the RFQ and we will come back with the confirmed figures. The AirTAC 3V2 and 3V3 valve bodies are the versions with published flow and coil-power data if you need numbers now.
One air connection feeds all stations; electricity belongs to the valves, not the block. Order a valve per station with the coil voltage your panel supplies, in DIN plug or flying-lead entry, and the manifold simply carries them on the shared supply.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V-F Base 3V300M8F
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.