Airtac 3V2M Solenoid Valve 3V2MNCFI-10F
The AirTAC Airtac 3V2M Solenoid Valve 3V2MNCFI-10F is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
- Valve type3/2-way (3-port, 2-position)
- Initial stateNormally closed
- Port size1/8 in
- Coil voltageDC12V
- Electrical entryFlying lead (lead-out wire type)
- Stations10
- Flow (Cv)0.1
- Series3V2M
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac 3V2M Solenoid Valve 3V2MNCFI-10F
The 3V2MNCFI-10F is a complete ten-station bank: ten normally closed 3/2 valve bodies mounted on a matched 10F base with one PT1/8 supply inlet and one shared wiring entry point. Every valve is direct-acting with a single solenoid and spring return, and the coaxial poppet shut-off holds a tight seal across the full 0-0.8 MPa range.
Each AC220V coil draws 7 VA, so a full bank under power presents 70 VA in total. The flying-lead construction gives you a pre-wired lead-out per valve instead of ten separate DIN plugs, which speeds cabinet routing. Because the valves are NC, every outlet stays vented until its coil energises - a natural failsafe for clamps and gates. IP65 (DIN 40050) protects the electrical parts.
Airtac 3V2M Solenoid Valve 3V2MNCFI-10F Technical Specifications
| Model | Airtac 3V2M Solenoid Valve 3V2MNCFI-10F |
|---|---|
| Series | 3V2M |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally closed |
| Item form | Complete assembly — 10 valves on a shared base |
| Exhaust | Centralised exhaust |
| Port size | 1/8 in |
| Thread | PT |
| Coil voltage | DC12V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 7.0 W |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Not rated for vacuum |
| Flow coefficient | Cv 0.1 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), base-mounted, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V2M catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
Model Code: Airtac 3V2M Solenoid Valve 3V2MNCFI-10F
| 3V2M | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/8 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NC | Normally closed: no air at the outlet until the coil is energised. |
| DC12V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| 10F | 10 stations in one assembly, centralised exhaust. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V2M Solenoid Valve 3V2MNCFI-10F Is Used
Packaging line clamp bank
Ten single-acting clamping cylinders on a carton-sealing machine switch from one 3V2MNCFI-10F bank; a power cut leaves every clamp released because the valves are normally closed.
Sorter gate control
Divert gates along a parcel conveyor each take one station of this ten-valve assembly, sharing a single supply and wiring run down the conveyor frame.
Test fixture actuation
An electronics end-of-line fixture with ten pusher or hold-down positions wires once to the manifold instead of terminating ten individual valves.
Is the Airtac 3V2M Solenoid Valve 3V2MNCFI-10F the Right Part?
3V2M puts manifold density first, so flow per valve is Cv 0.1. When one circuit needs more, build that station around an individual 3V2 valve (Cv 0.18 at 1/8 in, 0.19 at 1/4 in, and vacuum-rated) or move it to 3V3 (Cv 0.62, 1/4 in, vacuum-rated); where the duty is light and power matters, 3V1 runs at just 3.0 W on DC. A 3/2 valve feeds or vents a single outlet - it never drives a double-acting cylinder, which calls for the AirTAC 4V series.
Match five points before ordering: initial state, coil voltage, electrical entry, station count and exhaust type, plus thread (PT standard here; G or NPT on request). The NC state is fixed at purchase - it cannot be converted afterwards, so order NO at the outset if you need normally open.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V2M Solenoid Valve 3V2MNCFI-10F FAQ
Each valve has Cv 0.1, operates at 0-0.8 MPa (0-114 psi) and -20 to 70 C, and its AC220V coil draws 7 VA, giving 70 VA for ten energised stations. Protection is IP65 (DIN 40050), ports are PT1/8, and the medium is air filtered to 40 um or finer without lubrication.
No. 3V2M relies on a dedicated base gasket, and flipping or refitting it does not convert normally closed to normally open. The state is decided at order, so choose the NO variant when ordering if your circuit needs air to pass before energisation.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V2M Solenoid Valve 3V2MNCFI-10F
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.