Airtac 3V2M Solenoid Valve 3V2MNOCI-2F
The AirTAC Airtac 3V2M Solenoid Valve 3V2MNOCI-2F is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
- Valve type3/2-way (3-port, 2-position)
- Initial stateNormally open
- Port size1/8 in
- Coil voltageAC110V
- Electrical entryFlying lead (lead-out wire type)
- Stations2
- Flow (Cv)0.1
- Series3V2M
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac 3V2M Solenoid Valve 3V2MNOCI-2F
A normally open assembly inverts the fail logic: 3V2MNOCI-2F passes supply air to both outlets while de-energised and vents them when the AC110V coils are energised. Each of the two valve bodies is a direct-acting, spring-return 3/2 poppet with flying leads instead of DIN sockets, mounted on a 2-station base with centralised exhaust.
Normally open is chosen deliberately - for purge lines, vent interlocks or any duty where air must keep flowing through a control-circuit failure. It cannot be created after the fact: the NO state is built into the valve and its dedicated base gasket and cannot be reversed to NC. Both coils together draw 14 VA (7 VA each on AC110V), flow is Cv 0.1 per station, and the bodies are IP65 with manual overrides fitted.
Airtac 3V2M Solenoid Valve 3V2MNOCI-2F Technical Specifications
| Model | Airtac 3V2M Solenoid Valve 3V2MNOCI-2F |
|---|---|
| Series | 3V2M |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Item form | Complete assembly — 2 valves on a shared base |
| Exhaust | Centralised exhaust |
| Port size | 1/8 in |
| Thread | PT |
| Coil voltage | AC110V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 7 VA |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Not rated for vacuum |
| Flow coefficient | Cv 0.1 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), base-mounted, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V2M catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
Model Code: Airtac 3V2M Solenoid Valve 3V2MNOCI-2F
| 3V2M | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/8 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| AC110V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| 2F | 2 stations in one assembly, centralised exhaust. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V2M Solenoid Valve 3V2MNOCI-2F Is Used
Bolting station cooling purge
Two cooling-air nozzles on a bolting station keep blowing air across tool chucks while the line idles; de-energised NO valves let the purge continue, and energising stops it.
Fume cabinet sweep air
A university lab fume-cabinet air-knife pair stays open through controller faults because NO valves pass air until energised, keeping the sweep flow alive when power drops.
Grain spout dust jets
A depot grain-loading spout runs two dust-suppression air jets from one manifold; the NO valves keep the jets flowing during a control failure and shut only when the PLC commands it.
Is the Airtac 3V2M Solenoid Valve 3V2MNOCI-2F the Right Part?
Verify five points: NO state (fixed at purchase), AC110V coils, flying lead entry, two stations, centralised exhaust; PT1/8 is the standard port and G or NPT are catalogue options. Two stations suit a compact function pair; add capacity by ordering a longer base, since stations combine and expand freely. Where one function needs more flow than Cv 0.1, use a free-standing 3V2 (Cv 0.18 at 1/8, 0.19 at 1/4) or a 3V3 (Cv 0.62, 1/4); use 3V1 at 3.0 W DC when power draw is the constraint. Double-acting cylinders are outside 3/2 scope - specify the AirTAC 4V 5-port series.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V2M Solenoid Valve 3V2MNOCI-2F FAQ
3/2 normally open, Cv 0.1 per valve, 0-0.8 MPa (0-114 psi), -20 to 70 C, AC110V coils at 7 VA each (14 VA total), IP65 (DIN 40050), PT1/8 ports, with G and NPT to order.
NO keeps the outlet fed while de-energised, the right default when air must survive a control failure; NC shuts on failure. The state is fixed at manufacture and the dedicated base gasket cannot be reversed to convert NO to NC, so the choice is permanent once ordered.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V2M Solenoid Valve 3V2MNOCI-2F
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.