Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S
The AirTAC Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S is a genuine JIS-standard guided cylinder with a Ø16mm bore and 30mm stroke on twin guide rods. Its integrated steel-ball linear bearing gives low-friction, high-precision travel — well suited to vertical lifts and high-load, high-accuracy moves, holding the tool square to ±0.07° of rotation without any external linear guide.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- BearingSteel-ball linear bearing
- Non-rotating±0.07°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S
The B52-TCL16X30S is a JIS-standard guided twin-rod cylinder from AirTAC's copper-free build, where the B52- prefix designates a version free of copper and copper alloys for sensitive lines. Its drive piston runs between two guide rods carried in a steel-ball linear bearing, all in one body, so no external slide is needed. At 16mm bore it delivers 101 N of push at 0.5 MPa, and the +/-0.07 non-rotating tolerance keeps an off-centre gripper or plate square throughout travel.
The 30mm stroke suits compact pick-and-place cells and light vertical lifts where smooth, stick-slip-free motion matters. The steel-ball bearing gives the low-friction, high-precision travel that a plain bearing cannot match, while the 8mm piston rod and M5x0.8 ports keep the package small. Each end lands on a fixed TPU bumper rather than an adjustable air cushion, so there is no cushion screw to set or drift over time.
Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S Technical Specifications
| Model | Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S |
|---|---|
| Series | TCL JIS guided (twin-rod) cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Bearing | Steel-ball linear bearing |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.07° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 200 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 75 N |
| 0.7 MPa | 141 N | — |
| Max | 21 kgf | |
Force is set by the bore and piston rod (Ø8 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| L | Bearing: Steel-ball linear bearing (L = linear ball). |
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCM16X30 (brass sliding bearing, more impact/dust tolerant). Thread codes: blank = PT · G · T = NPT.
Where the Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S Is Used
Compact Pick-and-Place Gripper
A 101 N push at 0.5 MPa moves a small gripper in a parts-transfer cell, while the +/-0.07 anti-rotation keeps the jaws square to the workpiece. The steel-ball bearing prevents stick-slip during short, rapid strokes, so placement stays repeatable cycle after cycle.
Light Vertical Panel Lift
Lifting a thin panel or cover plate vertically, the 75 N pull at 0.5 MPa handles the return stroke, and the low-friction linear bearing avoids the jerky motion common with sliding bearings. The fixed TPU bumper softens the stop at each end without needing adjustment.
Lab Sample Positioning
In a lab instrument that indexes small vials or slides, the B52-TCL16X30S provides smooth, precise travel with 101 N of force. The copper-free build suits sensitive electronics and chemical environments, and the four sensor slots give flexible mounting for position feedback.
Is the Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S the Right Cylinder?
At 16mm bore, the next step down is 12 with 57 N of push at 0.5 MPa, while stepping up to 20 gives 157 N - useful if you need more margin for a heavier tool. The 16 rod is 8mm and ports are M5x0.8, with PT thread form as standard; the built-in magnet works with CS1 reed or DS1 electronic switches in the four body slots. If your application involves impact loads or a dusty environment, the TCM series with its brass sliding bearing is the better choice.
Remember that this cylinder does not hold its load if air pressure is lost - the rod will drift, since the guide resists rotation but not gravity. For a fail-safe hold, add an external rod lock or a pilot-operated check valve. The B52- prefix means copper-free construction; confirm the exact substituted materials with us before ordering for ammonia, battery, or electronics lines.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S FAQ
At 0.5 MPa, push is 101 N and pull is 75 N. At 0.7 MPa, push rises to 141 N. The theoretical maximum is 21 kgf at 1.0 MPa. These figures apply to the centre piston rod; the two guide rods carry side load and torque but do not add thrust.
B52- marks AirTAC's copper-free (copper-prohibited) build of the TCL16X30S, intended for lines where copper and copper alloys are not allowed, such as ammonia systems or certain battery and chemical plants. The exact material substitutions should be confirmed with us. The TCL series uses a steel-ball linear bearing for low-friction precision, while the TCM uses a brass sliding bearing for impact and dusty duty.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCL Cylinders
Request a Quote for Airtac B52-TCL Copper-Free Triple Rod Cylinder B52-TCL16X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.