Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK
The AirTAC Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK is a genuine two-in-one filter & regulator — a diversion-type water/particulate filter and a balanced pressure regulator built into ONE body. It has 1/2" ports, a 40 µm filter element and regulates 0.15 - 0.4 MPa (20 - 58 psi). It has no lubricator, so it adds no oil to the airflow.
- TypeFilter & regulator
- Port size1/2"
- Pressure range0.15 - 0.4 MPa (20 - 58 psi)
- Filtering grade40 µm
- Bowl materialPC
- Drainautomatic
- Pressure gaugeNot fitted
- Weight500 g
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK
The GAFR30015ALJNK is a filter and pressure regulator combined into a single body, so incoming air is cleaned and set to a steady outlet pressure without needing separate units. This 1/2in version operates in the lower 0.15-0.4 MPa (20-58 psi) band and uses a 40 um element, with no lubricator fitted anywhere in the design.
Its 60 cc condensate bowl collects water and solids spun out by the diversion structure, while the automatic drain clears it without manual attention. Weighing 500 g, this unit suits panel mounting rather than being supported by tubing, and the absent gauge means the 1/8in connection is ready for a later addition if readouts become necessary.
Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK Technical Specifications
| Model | Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK |
|---|---|
| Series | GAFR300 filter & regulator |
| Port size | 1/2" (PT thread) |
| Filtering grade | 40 µm |
| Pressure range | 0.15 - 0.4 MPa (20 - 58 psi) |
| Type | Lower pressure |
| Bowl material | PC |
| Drain type | Automatic drain |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Capacity of drain bowl | 60 cc |
| Bracket | Not included (J) |
| Weight | 500 g |
Specifications follow the official AirTAC GAFR catalogue (pages 235-236). Air must not freeze in the unit. No gauge is supplied with this model — the gauge connection on a GAFR300 is 1/8" if you add one. This unit filters and regulates only; it does not add lubrication.
Model Code: Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK
| GAFR300 | GA300 series filter & regulator — sets the port range, drain-bowl capacity and weight. |
|---|---|
| (blank) | Bowl material: PC. Available on this body: PC (blank), Metal (C), Nylon (N). |
| 15 | Port size 1/2". This body offers 08 = 1/4", 10 = 3/8", 15 = 1/2". |
| A | Drain: Automatic drain. |
| L | Lower pressure type — 0.15 - 0.4 MPa (20 - 58 psi). This body offers Standard (S) or Lower pressure (L). |
| J | No bracket (J) — supplied without the mounting bracket. |
| N | No pressure gauge; 1/8" gauge connection. |
| (blank) | Filtering grade 40 µm. |
| (blank) | PT thread; gauge scale MPa / psi. |
| K | Reverse-flow (reflux) valve attached. |
The filter and the regulator are ONE body here — there is no separate GAF filter or GAR regulator part to assemble. Need lubrication downstream too? Add a lubricator by ordering the matching GAFC300-15 F.R.L. combination instead.
Size Class & Flow Envelope
- GAFR2001/8"-1/4" · 2000 L/min
- GAFR3001/4"-1/2" · 3500 L/min
- GAFR4003/8"-1/2" · 7000 L/min
- GAFR5003/4" · 8000 L/min
- GAFR6003/4"-1" · 12000 L/min
Figures are the end of the flow curve plotted in the AirTAC catalogue at 0.7 MPa inlet pressure — a sizing envelope for comparing bodies, not a rated flow. Read the catalogue curve for a real duty point. Outlet pressure falls as flow rises, so size a body with headroom above your peak demand.
| This model | GAFR300 · 1/2" · curve to 3500 L/min |
|---|---|
| One size down | GAFR200 |
| One size up | GAFR400 (curve to 7000 L/min) |
| Add a lubricator | GAFC300-15 (F.R.L. combination) |
Where the Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK Is Used
Low-pressure assembly fixtures
Feed a bench-mounted press or clamping jig that operates below 0.4 MPa, where the lower pressure type prevents accidental over-pressurization of delicate tooling.
Instrument air for test rigs
Supply a leak-test station or calibration bench with filtered air at a stable low setpoint, using the automatic drain to keep the 60 cc bowl clear during long test runs.
Paint or coating lines
Regulate air for spray equipment in a finishing area, where the 40 um element traps particles and the lower pressure range matches typical atomization requirements.
Is the Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK the Right Air-Prep Unit?
Choose this GAFR300 body for 1/2in piping where the lower pressure range is sufficient, and step up to a GAFR400 if you need a 7000 L/min flow envelope at 0.7 MPa inlet. The PC bowl suits general duty, while the automatic drain handles wet or unattended lines, and the omitted bracket allows direct panel mounting. The 40 um element is the standard grade, and the PT thread matches common local fittings, with the reflux valve present as an ordering difference only. If oil is needed downstream, order the matching GAFC300-15 combination instead, since this unit does not lubricate. The 1.0 MPa max supply leaves about 0.6 MPa above the 0.4 MPa top of the range.
Quick checklist
- ✓ Body size for your peak flow (1/2" here)
- ✓ Standard 0.9 MPa or lower-pressure 0.4 MPa
- ✓ Bowl material: PC (blank), Metal (C), Nylon (N)
- ✓ Drain: semi-auto + manual, or automatic
- ✓ Element 40 µm or 5 µm
- ✓ Bracket kept or removed (J); add a lubricator = GAFC
Installation & Maintenance Notes
- check Install with the airflow arrow: IN to OUT, gauge/knob accessible.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Set pressure with the pressed-in self-locking knob; pull to adjust, press to lock.
- check Drain condensate before the 60 cc bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Support the 500 g unit on its bracket, not on the tubing.
This is a filter and regulator only — it delivers filtered, pressure-set air with no added oil. If a downstream tool needs lubrication, add a separate lubricator or order the GAFC300-15 combination; do not expect an oil mist from this unit.
Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK FAQ
It is a filter & regulator with a 1/2in port, working range 0.15-0.4 MPa (20-58 psi), max pressure 1.0 MPa (145 psi), proof pressure 1.5 MPa (215 psi), temperature range -5 to 70 C, 60 cc drain bowl, and 500 g weight. The element is 40 um, the drain is automatic, and no gauge or bracket is included.
The J code omits the mounting bracket for direct panel installation, and the N code means no gauge is supplied. The 1/8in gauge connection remains available if you add one later, but the set pressure cannot be read without fitting a gauge.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GAFR Adjustable Filter Regulator GAFR30015ALJNK
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, stock and lead time — usually within 7-8 hours.