AirTAC GFR200-08 Filter Regulator (GFR20008F3)
The AirTAC AirTAC GFR200-08 Filter Regulator (GFR20008F3) is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has PT1/4" ports, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
- TypeFilter regulator
- Port sizePT1/4"
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GFR200-08 Filter Regulator (GFR20008F3)
GFR20008F3 is an AirTAC G-series filter regulator: filtration and pressure regulation combined in a single body. This size 200 configuration takes a PT1/4 (PT thread, 1/4 in.) port, carries the standard 40 um element, and drains its polycarbonate bowl on the differential-pressure principle. An embedded square gauge reading in bar is included, a mounting bracket is included, and the regulator covers an adjust range of 0.15-0.9 MPa (20-130 psi) at up to 1.0 MPa (145 psi) inlet, with a working temperature of -5 to 70 C (non-freezing).
This is a genuine AirTAC part. The GFR family runs from size 200 to 600 with ports from 1/8 in. to 1 in., with choices of drain type, 40 um or 5 um (W) element, gauge type and scale, and G (BSPP) or NPT thread in place of the standard PT. AirTAC publishes G-series flow as curves rather than a single rated figure, so we confirm sizing and the full datasheet on request before you order.
AirTAC GFR200-08 Filter Regulator (GFR20008F3) Technical Specifications
| Model | AirTAC GFR200-08 Filter Regulator (GFR20008F3) |
|---|---|
| Series | GFR200 filter regulator |
| Port size | PT1/4" (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — square, bar scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GFR200-08 Filter Regulator (GFR20008F3)
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| 08 | Port size PT1/4". This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Mounting bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 3 | Gauge scale: bar. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
Size Class
- GFR200PT1/8" - PT1/4"
- GFR300PT1/4" - PT1/2"
- GFR400PT3/8" - PT1/2"
- GFR600PT3/4" - PT1"
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · PT1/4" · 40 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-08 (two-unit set) |
Where the AirTAC GFR200-08 Filter Regulator (GFR20008F3) Is Used
Bottling line capping heads
Feeds the pneumatic capping and settler cylinders on a bottling machine with water- and particle-strained air, while the bar gauge lets the line technician set and check cap pressure at a glance.
Packaging machine valve manifold
Sits ahead of the solenoid valve manifold on a cartoning or case-packing machine, conditioning the 1/4 in. branch supply so the manifold sees clean, correctly set pressure.
Welding fixture clamps
Supplies the pneumatic swing clamps on a weld fixture, holding a steady regulated setting across the shift so clamp force stays consistent part after part.
Is the AirTAC GFR200-08 Filter Regulator (GFR20008F3) the Right Unit?
Match the size digits (200/300/400/600) and port code (08 is 1/4 in.; 06, 10, 15, 20, 25 decode to 1/8, 3/8, 1/2, 3/4 and 1 in.) to your pipe run and the flow your line needs. Drain choice affects the setting window: differential-pressure drain (this model) gives 0.15-0.9 MPa (20-130 psi), manual-drain versions widen it to 0.05-0.9 MPa (7-130 psi), and automatic drain suits unattended duty. Stay with the standard 40 um element for general actuator supply, or order the W suffix for a 5 um element where downstream valves need finer filtration.
The embedded square gauge on this model reads in bar; round gauges in MPa or psi scales, G (BSPP) or NPT threads, and a bracketless (J) variant are catalogue options. Because flow is published as curves and not a single rating, send us your flow and pressure points and we will confirm the right size against the datasheet before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT1/4" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Oil needed downstream? Use GFC instead
Installation & Maintenance Notes
- check Mount vertically, bowl down, following the airflow arrow.
- check One body does the filtering and the regulating — no separate regulator needed.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC GFR200-08 Filter Regulator (GFR20008F3) FAQ
AirTAC publishes G-series flow as performance curves rather than one rated figure, so we do not quote a single number. Tell us your required flow and working pressure and we will confirm the correct size against the datasheet on request.
F denotes the embedded square gauge and 3 is the bar scale. The same series is also offered with round gauges (C) in MPa (1) or psi (2) scales, or with no gauge (N), all orderable variants of the identical size 200, PT1/4 unit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GFR200-08 Filter Regulator (GFR20008F3)
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.