AirTAC GR200-06 Pressure Regulator (GR20006LJC1)
The AirTAC AirTAC GR200-06 Pressure Regulator (GR20006LJC1) is a genuine G-series air pressure regulator. It holds a stable downstream pressure over the range 0.05 - 0.4 MPa (7 - 58 psi) with PT1/8" ports, and ships with a pressure gauge. A regulator does not filter the air — put a GF filter upstream, or use a GFR filter regulator, when water and particulate must also be removed.
- TypePressure regulator
- Port sizePT1/8"
- Regulating range0.05 - 0.4 MPa (7 - 58 psi)
- Pressure typeLow-pressure type
- Pressure gaugeFitted
- Reflux valveNot fitted
- ThreadPT
- BracketSupplied without bracket
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GR200-06 Pressure Regulator (GR20006LJC1)
The AirTAC GR20006LJC1 is a low-pressure type air pressure regulator from the G-series GR family. It reduces and holds downstream air pressure only - no filtration and no lubrication. This configuration has a 1/8 in PT port, an external round pressure gauge reading in MPa, and no mounting bracket (J), so it is mounted directly to the line or panel. As an L-type regulator its set-pressure range goes up to 0.4 MPa. Maximum working (inlet) pressure is 1.0 MPa (145 psi) and the service temperature range is -20 to 70 C.
This is a genuine AirTAC part. GR regulators are offered in sizes 200, 300, 400 and 600 with port, thread (PT standard, G and NPT options), gauge scale, bracket and check-valve choices. Flow is published as curves rather than a single rating, so we confirm the datasheet and sizing figures for your application on request.
AirTAC GR200-06 Pressure Regulator (GR20006LJC1) Technical Specifications
| Model | AirTAC GR200-06 Pressure Regulator (GR20006LJC1) |
|---|---|
| Series | GR200 pressure regulator |
| Port size | PT1/8" (PT thread) |
| Regulating range | 0.05 - 0.4 MPa (7 - 58 psi) |
| Pressure type | Low-pressure type |
| Bracket | Supplied without bracket |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -20 to +70 °C |
| Pressure gauge | Fitted — round, MPa scale |
| Reflux valve | Not fitted |
| Mounting | Panel mounting; optional fixing bracket |
Specifications follow the official AirTAC G-series air-preparation data. Note the GR temperature range is -20 to +70 °C, wider than the other G-series units. A regulator has no bowl and no filter element, so there is no filtering grade. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GR200-06 Pressure Regulator (GR20006LJC1)
| GR200 | G-series pressure regulator, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| L | Low-pressure type — 0.05 - 0.4 MPa (7 - 58 psi). Blank is standard, L is the low-pressure type. |
| J | Supplied without bracket. |
| (blank) | Pressure gauge fitted (blank). |
| C | Gauge shape: Round. C is round, F is square. |
| 1 | Gauge scale: MPa. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, type, bracket, gauge, gauge shape, scale, thread, reflux — a blank position takes the default. Example: GR300-08LNK is a 300 body, PT1/4", low-pressure type, no gauge, with reflux valve.
Size Class
- GR200PT1/8" - PT1/4"
- GR300PT1/4" - PT1/2"
- GR400PT3/8" - PT1/2"
- GR600PT3/4" - PT1"
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure.
| This model | GR200 · PT1/8" · 0.05 - 0.4 MPa (7 - 58 psi) |
|---|---|
| One size up | GR300 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GR200-06 Pressure Regulator (GR20006LJC1) Is Used
Instrument air trim on a control panel
Panels-mounted with no bracket, it trims the small instrument-air branch feeding transducers and pilot devices on a control cabinet to a stable low setpoint.
Point-of-use regulation at a maintenance drop
Installed at a workshop air drop so technicians running small air tools and blow-off guns work at a controlled low pressure instead of full header pressure.
Zone control on a modular automation cell
Plumbed inline in a compact automation cell to give one module its own low-pressure supply, independent of neighbouring stations sharing the same header.
Is the AirTAC GR200-06 Pressure Regulator (GR20006LJC1) the Right Regulator?
Check the port first: this 200-size code uses a 1/8 in PT connection; step up to GR300/GR400/GR600 for bigger lines and higher demand. This is the L (low-pressure) type for settings up to 0.4 MPa. The J in the code means no bracket, so plan for direct piping or your own panel mount; GR bodies are also panel-mountable. The C1 suffix gives an external round gauge in MPa - pick a square embedded gauge, or psi/bar scales, if preferred. Thread is PT as standard with G and NPT options. Flow is published as curves, not a single rating, so ask us to confirm sizing before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT1/8" here)
- ✓ Standard 0.9 MPa or low-pressure 0.4 MPa
- ✓ Gauge fitted, or order N without
- ✓ Gauge shape C round / F square
- ✓ Scale MPa (1), psi (2) or bar (3)
- ✓ Reflux valve needed, order K
Installation & Maintenance Notes
- check Install downstream of the filter, following the airflow arrow.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Set pressure while air is flowing, then lock the knob.
- check Adjust within 0.05 - 0.4 MPa (7 - 58 psi) only.
- check Operating range -20 to +70 °C.
- check Panel-mount or use the fixing bracket; do not hang it on tubing.
Without a reflux valve, air cannot flow back through the regulator — order the K option if reverse flow is required. A regulator does not remove water or particulate; that is the filter's job.
AirTAC GR200-06 Pressure Regulator (GR20006LJC1) FAQ
There is no single rated flow to quote - AirTAC publishes GR regulator flow as curves. Send us your air demand and line size and we will confirm the datasheet figures and check this 1/8 in size is right for your application on request.
J means the mounting bracket is omitted, so this regulator mounts directly in the line or to a panel. If you want the bracket included, choose the same configuration without the J in the code.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GR200-06 Pressure Regulator (GR20006LJC1)
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.