AirTAC GR600-25 Pressure Regulator (GR60025F1G)
The AirTAC AirTAC GR600-25 Pressure Regulator (GR60025F1G) is a genuine G-series air pressure regulator. It holds a stable downstream pressure over the range 0.05 - 0.9 MPa (7 - 130 psi) with PT1" ports, and ships with a pressure gauge. A regulator does not filter the air — put a GF filter upstream, or use a GFR filter regulator, when water and particulate must also be removed.
- TypePressure regulator
- Port sizePT1"
- Regulating range0.05 - 0.9 MPa (7 - 130 psi)
- Pressure typeStandard type
- Pressure gaugeFitted
- Reflux valveNot fitted
- ThreadG (BSPP)
- BracketFixing bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GR600-25 Pressure Regulator (GR60025F1G)
The AirTAC GR60025F1G is a G-series compressed-air pressure regulator with a 1 in G (BSPP) parallel thread, the standard-pressure type, and an embedded square gauge scaled in MPa. It is a pure regulator: it sets and holds downstream pressure only, with no filter, no bowl and no lubrication in the body.
This is a genuine AirTAC part from the GR range in 200, 300, 400 and 600 sizes. Choose NPT or PT threads, a low-pressure type (up to 0.4 MPa), a reverse check valve, gauge scales in MPa, psi or bar, and bracket or panel mounting to suit the install. Maximum inlet pressure is 1.0 MPa (145 psi); working temperature is -20 to 70 C. Flow appears in the catalogue only as curves, so we confirm flow and datasheet figures on request.
AirTAC GR600-25 Pressure Regulator (GR60025F1G) Technical Specifications
| Model | AirTAC GR600-25 Pressure Regulator (GR60025F1G) |
|---|---|
| Series | GR600 pressure regulator |
| Port size | PT1" (G (BSPP) thread) |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Standard type |
| Bracket | Fixing bracket included |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -20 to +70 °C |
| Pressure gauge | Fitted — square, MPa scale |
| Reflux valve | Not fitted |
| Mounting | Panel mounting; optional fixing bracket |
Specifications follow the official AirTAC G-series air-preparation data. Note the GR temperature range is -20 to +70 °C, wider than the other G-series units. A regulator has no bowl and no filter element, so there is no filtering grade. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GR600-25 Pressure Regulator (GR60025F1G)
| GR600 | G-series pressure regulator, 600 body — sets the port range. |
|---|---|
| 25 | Port size PT1". This body offers 20 = PT3/4", 25 = PT1". |
| (blank) | Standard type — 0.05 - 0.9 MPa (7 - 130 psi). Blank is standard, L is the low-pressure type. |
| (blank) | Fixing bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 1 | Gauge scale: MPa. 1 is MPa, 2 is psi, 3 is bar. |
| G | G (BSPP) thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, type, bracket, gauge, gauge shape, scale, thread, reflux — a blank position takes the default. Example: GR300-08LNK is a 300 body, PT1/4", low-pressure type, no gauge, with reflux valve.
Size Class
- GR200PT1/8" - PT1/4"
- GR300PT1/4" - PT1/2"
- GR400PT3/8" - PT1/2"
- GR600PT3/4" - PT1"
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure.
| This model | GR600 · PT1" · 0.05 - 0.9 MPa (7 - 130 psi) |
|---|---|
| One size down | GR400 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GR600-25 Pressure Regulator (GR60025F1G) Is Used
Compressor after-cooler outlet control
Mounted on the 1 in G-threaded outlet of a compressor and after-cooler skid, setting the pressure delivered into the plant ring main.
Textile machine air jet supply
Installed on the metric-threaded air supply of weaving and spinning machines, holding the set pressure that jet nozzles and actuators depend on.
Panel-mounted machine air circuit
Panel-mounted inside a machine control cabinet, giving operators a front-facing MPa gauge and adjustment point for the whole pneumatic section.
Is the AirTAC GR600-25 Pressure Regulator (GR60025F1G) the Right Regulator?
Pick the G (BSPP) thread on this code when your piping or components are specified in metric parallel thread; the same regulator is available as GR60025F1 in PT or with an NPT option if your hardware is tapered imperial. The 600 size with a 1 in port is the top of the G-series range - use it for high-demand main lines and drop to 300 or 400 sizes for smaller branches. The gauge is the embedded square type in MPa; F2 and F3 variants give psi and bar scales.
Standalone GR adjustment range is 0.05-0.9 MPa. A bracket is included and the GR series is panel-mountable as well. Since flow is published only as curves with no single rated figure, ask us to confirm sizing against the application datasheet before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT1" here)
- ✓ Standard 0.9 MPa or low-pressure 0.4 MPa
- ✓ Gauge fitted, or order N without
- ✓ Gauge shape C round / F square
- ✓ Scale MPa (1), psi (2) or bar (3)
- ✓ Reflux valve needed, order K
Installation & Maintenance Notes
- check Install downstream of the filter, following the airflow arrow.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Set pressure while air is flowing, then lock the knob.
- check Adjust within 0.05 - 0.9 MPa (7 - 130 psi) only.
- check Operating range -20 to +70 °C.
- check Panel-mount or use the fixing bracket; do not hang it on tubing.
Without a reflux valve, air cannot flow back through the regulator — order the K option if reverse flow is required. A regulator does not remove water or particulate; that is the filter's job.
AirTAC GR600-25 Pressure Regulator (GR60025F1G) FAQ
AirTAC gives GR flow performance only as curves, not as a single rated figure, so we do not quote a number here. Tell us your inlet pressure, set pressure and consumption, and we will confirm the flow from the datasheet on request.
No. The trailing G on GR60025F1G means a 1 in G (BSPP) parallel thread; the base GR60025F1 carries PT as the standard. NPT is also a catalogue option. Match the thread to your pipework when you order - it is a specification choice, so check which system your plant uses.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GR600-25 Pressure Regulator (GR60025F1G)
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.