Airtac HLSL Precision Slide Table Cylinder HLSL20X100S
The AirTAC Airtac HLSL Precision Slide Table Cylinder HLSL20X100S is a genuine HLS slide-table cylinder, 20 mm bore: a double-acting dual-rod air cylinder integrated with a cross-roller guide so the table travels straight with high rigidity and low deflection. It delivers about 236 N of push at 0.5 MPa. This is the symmetrical version. A floating joint spares the rod from side torque; the magnet is fitted as standard.
- TypeSlide-table, double acting
- Guidecross-roller guide
- Bore20 mm
- Push thrust @0.5 MPa236 N
- Operating pressure0.15 - 0.7 MPa (22 - 100 psi)
- Port size1/8"
- CushionBumper (+ shock-absorber option)
- Magnet / sensorStandard; CMSH/DMSH/EMSH
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac HLSL Precision Slide Table Cylinder HLSL20X100S
The HLSL20X100S is a symmetrical cross-roller slide table cylinder combining a bore 20 mm AirTAC cylinder with a 100 mm stroke and an integrated linear guide. The dual-rod design applies thrust from two opposing pistons, giving more push than a single-rod cylinder of the same bore, while the floating joint spares the rods from side torque applied by the workpiece. The cross-roller guide delivers high rigidity and low deflection over the full 100 mm of travel, useful for wider transfer moves and machine mounting where straight, stable travel matters.
This is a genuine AirTAC part ordered under the full factory code. The magnet is standard on the entire series, so CMSH, DMSH or EMSH switches can be clipped into the body slots for end-of-stroke sensing without special options. The basic version uses bumper cushions at both ends. Thrust figures, overall dimensions and the load and moment data are published in the datasheet and the on-page spec table, and we will confirm them for your application on request.
Airtac HLSL Precision Slide Table Cylinder HLSL20X100S Technical Specifications
| Model | Airtac HLSL Precision Slide Table Cylinder HLSL20X100S |
|---|---|
| Type | Slide-table cylinder, double acting, dual rod |
| Series / guide | HLSL (cross-roller guide) |
| Bore | 20 mm |
| Push thrust @0.5 MPa | 236 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 0.7 MPa (22 - 100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to 70 C |
| Speed range | 50 - 500 mm/s (meter-out) |
| Cushion | Bumper; shock-absorber / adjustable-stopper options |
| Magnet / sensor | Standard; CMSH, DMSH, EMSH |
Specifications follow the official AirTAC HL slide-table data. Max working pressure is 0.7 MPa. The table rides on an integrated linear guide — do not apply strong impact or large moment. Allowable load and moment are published as tables and curves, and overall dimensions vary per stroke — ask us and we confirm from the datasheet.
How to choose
Bore 20 gives higher thrust than the 16 mm models in this series while staying within the 0.15-0.7 MPa operating range; move to bore 25 if you need more push, or down to 16 for lighter duty. The 100 mm stroke is within the bore's published stroke table. For guide choice, HLS/HLSL cross-roller tables top the range for rigidity and load, HLQ ball-bearing tables add anti-rust, dust-proof travel, HLH miniature roller-ball units offer the best straightness in smaller bores, and HLF gives a low-height cross-roller body. This basic code has bumper cushions only; if your stops need tuning, order the A (adjustable rubber stopper) or B (shock absorber) codes available on HLS/HLQ. Thread is PT as standard, with G and NPT options. Route your load and moment sizing to us and we will check it against the published tables and deflection curves.
Applications
Small-parts transfer
Push or index trays of small parts along a 100 mm transfer step, with the cross-roller guide keeping the table square to the conveyor line.
Pick-and-place module
The wider 100 mm travel suits pick-and-place heads that move components from a feeder to a nest, with the floating joint absorbing mounting misalignment.
Stopper and eject position
Use the guided table as a precise stopper or ejector on an assembly line, where dual-rod thrust resists side loading from arriving parts.
FAQ
Do I need to order a magnet option for position sensing?
No. The magnet is standard on the whole HLS/HLSL series and cannot be declined. Fit a CMSH, DMSH or EMSH switch into the slots on the body to sense table position at either end of the 100 mm stroke.
How much pressure can I run into HLSL20X100S?
The maximum working pressure is 0.7 MPa (100 psi); proof pressure is 1.2 MPa. This bore operates from 0.15 to 0.7 MPa (22-100 psi) on clean, filtered air, with speed held between 50 and 500 mm/s using meter-out control.