Airtac JSI Series Standard Cylinder JSI100X600TC
The AirTAC Airtac JSI Series Standard Cylinder JSI100X600TC is a genuine double acting JIS-standard air cylinder with a Ø100mm bore and 600mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke600 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSI Series Standard Cylinder JSI100X600TC
Delivering 3927 N of push force at 0.5 MPa, this double-acting JIS-standard profile cylinder is built for heavy-duty automation. Its extruded hard-anodized aluminum barrel omits external rods, making the unit shorter and more compact than an ISO 15552 cylinder of the same 100 mm bore. The internal two-way piston seal retains grease for a long, low-friction service life. Because this SKU lacks the -S magnet, it cannot accept CMSE or DMSE position switches.
With a 600 mm stroke, the G1/2 ported actuator provides substantial travel. Plan for about 2356 N of real work at 0.5 MPa, which means it lifts roughly 200 kg vertically with a 2:1 safety margin. The adjustable 33 mm air cushions at both ends decelerate the heavy 32 mm chrome rod smoothly, and you can pair it with a TC trunnion mount for pivoting articulation.
Airtac JSI Series Standard Cylinder JSI100X600TC Technical Specifications
| Model | Airtac JSI Series Standard Cylinder JSI100X600TC |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac JSI Series Standard Cylinder JSI100X600TC
| JSI | JIS-standard profile cylinder (double-acting type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSI Series Standard Cylinder JSI100X600TC Is Used
Pallet Transfer Line
Uses the 600 mm stroke to push heavy loaded pallets sideways between adjacent roller conveyors in packaging facilities.
Vertical Material Gate
Raises and lowers a 150 kg security gate on a storage carousel, relying on the 100 mm bore to deliver consistent upward thrust.
Automated Press Feed
Advances thick steel blanks into a stamping press, utilizing the adjustable end cushions to soften the deceleration of heavy stock.
Is the Airtac JSI Series Standard Cylinder JSI100X600TC the Right Cylinder?
If 3927 N of push is excessive, the smaller 80 mm bore yields 2513 N at 0.5 MPa; if your application demands more power, stepping up to the 125 mm bore provides 6136 N. Because this 600 mm stroke is long, external guide rails are strongly recommended to prevent rod bending under side loads. The TC trunnion mount helps absorb angular misalignment along the extended axis.
Remember that a standard actuator drifts when air is lost or the valve is centered, as the cushions only decelerate near stroke end rather than locking the piston. To suspend a vertical load safely, install an external rod lock or a pilot-operated check valve. Since this specific model has no -S suffix, it cannot host magnetic sensors; choose the -S variant if you need CMSE or DMSE switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSI Series Standard Cylinder JSI100X600TC FAQ
This 100 mm bore cylinder features a G1/2 port and a 32 mm piston rod. It generates 3927 N push and 3574 N pull at 0.5 MPa, 5497 N push and 5003 N pull at 0.7 MPa, with a theoretical maximum of 801 kgf at 1.0 MPa.
The JIS-standard extruded profile design is shorter and more compact than an ISO 15552 cylinder of the same bore, saving machine space. It uses a TC trunnion mount for pivoting, and because this SKU lacks the -S magnet, it cannot accept magnetic sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSI Series Standard Cylinder JSI100X600TC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.