Airtac MDJ Adjustable Cylinder MDJ25X25-30
The AirTAC Airtac MDJ Adjustable Cylinder MDJ25X25-30 is a genuine MD multi-mount cylinder (adjustable stroke), 25 mm bore. Its compact square body fixes from six directions and mounts side by side to save space. It delivers about 245.4 N of push force at 0.5 MPa. A bumper cushions the impact.
- TypeMulti-mount, adjustable stroke
- SeriesMD (standard)
- Bore25 mm
- Push thrust @0.5 MPa245.4 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port sizeM5x0.8
- CushionBumper
- MagnetWithout magnet
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MDJ Adjustable Cylinder MDJ25X25-30
The MDJ25X25-30 is an adjustable-stroke multi-mount cylinder whose square body fixes from six directions: front, back, left, right, top and bottom. Units mount side by side to save space, with magnetic-switch slots around the body and high guide precision without added lubricant. The double-acting 25 mm bore gives about 245.4 N theoretical push thrust at 0.5 MPa, with a bumper providing cushioning - a good fit for positioning jobs where the end of stroke must be trimmed to the application.
This is a genuine AirTAC part from the standard MD family; the MK family is the no-rotating equivalent. This SKU has no magnet, so it is best where switch detection is not needed. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s. We confirm dimensions and sizing from the datasheet on request.
Airtac MDJ Adjustable Cylinder MDJ25X25-30 Technical Specifications
| Model | Airtac MDJ Adjustable Cylinder MDJ25X25-30 |
|---|---|
| Type | Multi-mount cylinder, adjustable stroke |
| Series | MD (standard) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 245.4 N |
| Port size | M5x0.8 (PT thread) |
| Magnet | Without magnet |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper |
| Mounting | Fix from 6 directions; mountable side by side |
Specifications follow the official AirTAC MD/MK multi-mount data. The front cover and piston are short, so avoid an over-long stroke. An optional high-temperature seal material extends the range to 0 to 150 C. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
The 25 mm bore provides about 245.4 N theoretical push thrust at 0.5 MPa; drop to a smaller bore for lighter loads. MDJ gives a 25 mm base stroke plus a 30 mm adjustable range - the widest trim window in this series - so the effective stroke is set between 25 and 55 mm. Double acting powers both directions. This code carries no magnet; choose the S version if you need switch detection. Thread is PT, with G available. Respect the bore's stroke table and short covers - avoid over-long strokes - and route side-load questions to us.
Applications
Gate and stopper actuation
Fix the body from the top or side of a conveyor line to drive a swing gate or stopper, with the 30 mm adjustable range dialling in the throw.
Part lift and lower
Mount under a small fixture to raise and lower parts between stations, using the double-acting 25 mm bore for controlled motion in both directions.
Press-fit assist
Set the adjustable stroke to apply around 245.4 N of push at 0.5 MPa for light pressing or seating tasks on compact assemblies.
FAQ
Does the MDJ25X25-30 include a magnet?
No. With no trailing S in the code, this SKU is supplied without a magnet, and magnet fitment is optional on this series rather than standard. If you need pneumatic switch detection on the body slots, order the MDJ25X25-30S variant instead.
How far can I adjust the stroke, and is there a limit?
This model has a 25 mm base stroke with a 30 mm adjustable range on top, so the effective stroke is set anywhere between them. Keep the total within the bore's stroke table - the short covers caution against over-long strokes - and confirm any side-load requirement with us before finalising the design.