Airtac PB Pen-type Cylinder PB16X10UFA
The AirTAC Airtac PB Pen-type Cylinder PB16X10UFA is a double-acting pen-size (mini) air cylinder with a Ø16mm bore and 10mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ16 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM10×1.0
- CushionElastic bumper (both ends)
About the Airtac PB Pen-type Cylinder PB16X10UFA
The AirTAC PB16X10UFA is a JIS double-acting single-rod pen-size mini cylinder engineered for short, high-frequency motions. It supplies 100.5 N of push and 90.7 N of pull at 0.5 MPa, operating through a 10 mm stroke. The slim SUS304 stainless barrel and piston rod resist damp environments, while the compact profile minimizes mass on moving carriages.
This specific configuration features a U 90-degree perpendicular side air inlet for flat plumbing alongside an FA mounting bracket. Air connects via an M5x0.8 port, and the Ø5 mm rod terminates in an M10x1.0 thread. Because the fixed TPU bumper at each end only absorbs the final few millimeters of travel, high-speed cycling with heavy tooling requires metering out the exhaust or adding an external shock absorber.
Airtac PB Pen-type Cylinder PB16X10UFA Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB16X10UFA |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø16 mm |
| Rod diameter | Ø5 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 100.5 N | 90.7 N |
| 0.7 MPa (max) | 140.7 N | 126.9 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB16X10UFA
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 16 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB16X10UFA Is Used
PCB Depaneling Jig
Provides a short 10 mm thrust to snap separated circuit boards out of a routing fixture without stressing adjacent components.
Blister Pack Tamp
Presses thin plastic lids into carrier pockets on a high-speed packaging line, utilizing the 100.5 N output for a firm seal.
Sorter Diverter Gate
Actuates a lightweight flap to redirect small pharmaceutical bottles exiting a filling station, fitting neatly within tight conveyor clearances.
Is the Airtac PB Pen-type Cylinder PB16X10UFA the Right Cylinder?
Selecting this 16 mm bore yields 100.5 N push at 0.5 MPa. If you need less force, stepping down to the 12 mm bore provides 56.5 N, while moving up is unnecessary as 16 mm is the largest in this family. Plan for a safe working load of about 60 N, which accounts for roughly 60% of the theoretical 0.5 MPa output to overcome seal friction. For vertical lifts, expect to raise approximately 5.1 kg safely with a 2:1 margin.
Remember that a standard double-acting cylinder drifts when air pressure is lost or the valve is centered, as the bumper decelerates but does not lock the piston. If your process demands fail-safe position holding, install an external rod lock. When ordering, confirm the 16 mm bore, 10 mm stroke, U side inlet, FA bracket, and the absence of a sensor magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB16X10UFA FAQ
At 0.5 MPa this cylinder generates 100.5 N of push and 90.7 N of pull. At the maximum operating pressure of 0.7 MPa, push increases to 140.7 N and pull to 126.9 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s.
The U cover provides a 90-degree side air inlet for flat plumbing in confined spaces, while the FA bracket allows secure front mounting. The Ø5 mm stainless rod is designed for coaxial thrust, so avoid side loading and add an external guide if moving off-axis loads over the 10 mm stroke.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB16X10UFA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.