Airtac SGC Standard Cylinder SGC160X700
The AirTAC Airtac SGC Standard Cylinder SGC160X700 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø160mm bore and 700mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ160 mm
- Stroke700 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC160X700
Delivering 10053 N of push force at 0.5 MPa, this double-acting ISO 15552 tie-rod cylinder is built for heavy-duty automation. Four steel tie rods clamp the aluminium barrel to the covers for high rigidity, while a two-way piston seal maintains an internal oil reservoir for long service life. The G3/4 port and M36x2.0 rod thread handle the high airflow and mechanical load demanded by large-bore pneumatics.
Because this SKU lacks the -S magnet option, it cannot accept CMSG, DMSG, or EMSG position switches. Plan for about 6032 N of actual work at 0.5 MPa, which means it lifts roughly 512 kg vertically with a 2:1 safety margin. The standard TPU seals operate from -20 to +70 C, though a Viton H option extends this to 0-150 C.
Airtac SGC Standard Cylinder SGC160X700 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC160X700 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø160 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 10053 N | 9425 N |
| 0.7 MPa | 14074 N | — |
| Max (@1.0 MPa) | 2050 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC160X700
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 160 | Bore size in mm (125 / 160 / 200 / 250). |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC160X700 Is Used
Press Ejection
Ejects heavy formed metal parts from hydraulic presses, utilizing the 10053 N push force to clear the die area reliably during automated stamping cycles.
Pallet Handling
Indexes loaded pallets along heavy-duty transfer lines, where the 700 mm stroke accommodates wide conveyor transitions without requiring multi-stage actuators.
Automated Assembly Lifts
Raises large machinery subframes into position on assembly lines, depending on external guides to maintain alignment over the extended 700 mm travel distance.
Is the Airtac SGC Standard Cylinder SGC160X700 the Right Cylinder?
When sizing this 160 mm bore actuator, compare it against its neighbours: the 125 mm bore yields 6136 N of push at 0.5 MPa, while the 200 mm bore provides 15708 N. If your fixture relies on the ISO 15552 mounting interface, this model drops directly into existing LB foot, FA flange, or TC trunnion hardware. Since this specific configuration has no -S suffix, you must select an external mechanical limit switch if position feedback is required.
Running a 700 mm stroke on a large-bore piston generates significant leverage, so external guide rails are strongly recommended to prevent rod bending under side loads. Furthermore, the 50 mm adjustable air cushions at both ends only decelerate the piston near stroke end; they do not act as a brake. If the load must be prevented from drifting when air pressure is lost or the valve is centred, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC160X700 FAQ
The 160 mm bore generates a push force of 10053 N and a pull force of 9425 N at 0.5 MPa. At 0.7 MPa, push is 14074 N and pull is 13194 N. The theoretical maximum force is 2050 kgf at 1.0 MPa. It uses a G3/4 air port and a 50 mm adjustable air cushion at both ends.
No, because this specific model lacks the -S magnet suffix, it cannot accept CMSG, DMSG, or EMSG magnetic switches. You would need the -S variant for magnetic sensing, or use external mechanical switches. The unit is built with a genuine ISO 15552 tie-rod mounting interface for interchangeability with standard large-bore fixtures.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC160X700
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.