Airtac SGC Standard Cylinder SGC200X1100
The AirTAC Airtac SGC Standard Cylinder SGC200X1100 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 1100mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke1100 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X1100
Delivering 15708 N of push force at 0.5 MPa, this double-acting large-bore cylinder handles heavy-duty automation with ease. The Ø200 mm bore uses a G3/4 air port and a M36x2.0 rod thread, driving a 1100 mm stroke. Four steel tie rods clamp the aluminum barrel to the covers for high structural rigidity, while the two-way piston seal maintains an internal oil reservoir to maximize service life. Plan for about 9425 N of real work at 0.5 MPa, which safely lifts an 801 kg vertical load with a 2:1 margin.
Dimensionally interchangeable per the ISO 15552 mounting interface, it drops directly into existing large-bore fixtures without custom brackets. This specific SKU lacks the -S magnet, so it cannot accept CMSG, DMSG, or EMSG position switches. The standard TPU seals operate from -20 to +70 C, though a Viton H option extends heat resistance up to 150 C.
Airtac SGC Standard Cylinder SGC200X1100 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X1100 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 1100 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X1100
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×1100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X1100 Is Used
Automotive Press Stamping
Provides the robust 15708 N push force required to actuate heavy lower dies in large stamping presses over a 1100 mm extension.
Palletizer Strapping
Drives massive strapping and positioning heads across 1100 mm spans to secure heavy unit loads on outbound shipping pallets.
Injection Mold Extraction
Pushes large molded automotive panels completely out of heavy machinery using a rigid tie-rod build that resists deflection.
Is the Airtac SGC Standard Cylinder SGC200X1100 the Right Cylinder?
When sizing this 200 mm bore, compare your actual load against the 15708 N push at 0.5 MPa. If you need less force, the smaller Ø160 bore provides 10053 N; stepping up to the Ø250 bore yields 24543 N. Because this model features a 1100 mm stroke, you must use external guide rails to prevent rod bending and absorb side loads during long extensions.
Remember that a standard cylinder drifts when air is lost or the valve is centered, as the adjustable 50 mm air cushions only decelerate the piston near stroke ends rather than locking it. For suspended loads that must hold position, integrate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X1100 FAQ
This Ø200 mm bore model features a G3/4 air port and delivers 15708 N push / 15079 N pull at 0.5 MPa, 21991 N push / 21110 N pull at 0.7 MPa, and a theoretical maximum of 3204 kgf at 1.0 MPa.
No, this specific SKU does not include the -S magnet, so it cannot host CMSG, DMSG, or EMSG switches. You must select an -S variant to enable magnetic sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X1100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.