Airtac SGC Standard Cylinder SGC200X135S
The AirTAC Airtac SGC Standard Cylinder SGC200X135S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 135mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke135 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X135S
Delivering 15708 N of push force at 0.5 MPa, this large-bore AirTAC actuator utilizes a robust tie-rod design where four steel rods clamp the aluminum barrel to the covers for extreme rigidity. The double-acting single rod runs on a 40 mm chrome-plated shaft and features a G3/4 air port. Plan for roughly 9425 N of real work at 0.5 MPa, which safely lifts about 801 kg vertically with a 2:1 margin.
Because this SKU includes the -S magnet, it readily accepts CMSG, DMSG, or EMSG electronic switches for position sensing. The standardized ISO 15552 mounting interface guarantees it drops directly into existing large-bore fixtures, while the two-way piston seal maintains an internal oil reservoir to maximize operational lifespan.
Airtac SGC Standard Cylinder SGC200X135S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X135S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 135 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X135S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×135 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X135S Is Used
Heavy Stamping Press
Provides the high 21991 N push force at 0.7 MPa required to actuate heavy-duty stamping dies and form thick steel plates.
Pallet Stopper Gate
Functions as a rugged 135 mm stroke barrier gate to halt 800 kg loaded pallets on high-speed conveyor lines.
Injection Mold Clamp
Secures large injection molding tooling halves using its rigid four tie-rod construction and M36x2.0 rod thread.
Is the Airtac SGC Standard Cylinder SGC200X135S the Right Cylinder?
When sizing this 200 mm bore option, compare it against its neighbors: a 160 mm bore yields 10053 N push at 0.5 MPa, whereas stepping up to the 250 mm bore provides 24543 N. The 135 mm stroke falls well under the 1500 mm maximum, so standard rod-bending concerns are minimal, but always verify side-load alignment. This model's built-in magnet supports CMSG/DMSG/EMSG sensors without extra hardware.
Remember that the adjustable 50 mm air cushions at both ends only decelerate the piston near stroke end; they do not function as a brake. If gravity or air loss could cause the piston to drift and drop a load, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X135S FAQ
This 200 mm bore cylinder features a G3/4 air port and an M36x2.0 rod thread. It generates 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum of 3204 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so it fits standard FA/FB flanges and TC trunnions. The -S suffix indicates a built-in magnet for direct mounting of CMSG, DMSG, or EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X135S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.