Airtac SGC Standard Cylinder SGC200X400SH
The AirTAC Airtac SGC Standard Cylinder SGC200X400SH is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 400mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke400 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X400SH
Delivering 15708 N of thrust at 0.5 MPa, this 200 mm bore tie-rod actuator handles heavy automation tasks. The SGC200X400SH features a 400 mm stroke, a G3/4 air port, and a robust M36x2.0 piston rod. Four steel tie rods clamp the aluminum barrel to the covers, providing the rigidity needed for high-force cycles. The standard Viton H seal allows operation up to 150 C, replacing the default TPU for harsh environments.
Because it follows the ISO 15552 mounting interface, this cylinder drops directly into existing large-bore fixtures. The built-in -S magnet supports CMSG, DMSG, and EMSG switches for position detection. For practical sizing, plan for about 9425 N of real work at 0.5 MPa, which equates to lifting roughly 801 kg vertically with a 2:1 safety margin.
Airtac SGC Standard Cylinder SGC200X400SH Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X400SH |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X400SH
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X400SH Is Used
Injection Mold Clamping
Applies 15708 N of thrust at 0.5 MPa to secure heavy injection mold halves, utilizing the Viton H seal to withstand ambient heat near the barrel.
Pallet Stopper Gate
Acts as a high-force stop gate on heavy-duty pallet conveyors, absorbing impact via the 50 mm adjustable air cushions at both ends.
Press Ejection System
Ejects dense metal parts from hydraulic presses over a 400 mm travel, relying on the rigid four-tie-rod construction to resist deflection.
Is the Airtac SGC Standard Cylinder SGC200X400SH the Right Cylinder?
When sizing this 200 mm bore unit, consider the adjacent SGC options: the 160 mm bore provides 10053 N push at 0.5 MPa, while the 250 mm bore offers 24543 N. This SGC200X400SH includes the Viton H seal for 0-150 C high-temperature environments. The 400 mm stroke is well within standard limits, but always ensure external guides support side loads to prevent rod bending. Note that an unpowered cylinder drifts; the air cushions only decelerate the piston near stroke end and do not act as a brake. Use an external rod lock or pilot-operated check valve for secure load holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X400SH FAQ
This 200 mm bore cylinder features a G3/4 air port and an M36x2.0 rod thread. It generates 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum of 3204 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, so it fits standard large-bore accessories. The included -S magnet allows direct mounting of CMSG, DMSG, or EMSG switches for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X400SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.