Airtac TCL Triple Axis Cylinder TCL12X40-S
The AirTAC Airtac TCL Triple Axis Cylinder TCL12X40-S is a genuine JIS-standard guided cylinder with a Ø12mm bore and 40mm stroke on twin guide rods. Its integrated steel-ball linear bearing gives low-friction, high-precision travel — well suited to vertical lifts and high-load, high-accuracy moves, holding the tool square to ±0.08° of rotation without any external linear guide.
- BoreØ12 mm
- Stroke40 mm
- Port sizeM5×0.8
- BearingSteel-ball linear bearing
- Non-rotating±0.08°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCL Triple Axis Cylinder TCL12X40-S
The AirTAC TCL12X40-S is a JIS guided twin-rod double-acting cylinder integrating a steel-ball linear bearing. A drive piston moves between two guide rods in one body, eliminating the need for an external linear slide. It generates 57 N of push at 0.5 MPa and holds a non-rotating accuracy of ±0.08°, keeping small grippers square under offset loads.
This compact 12 mm bore unit features an Ø6 mm piston rod and M5x0.8 ports. The low-friction steel-ball bearing ensures smooth travel without stick-slip, making it well-suited for vertical lifts. Stroke ends are absorbed by fixed TPU bumpers, as no adjustable air cushion is present.
Airtac TCL Triple Axis Cylinder TCL12X40-S Technical Specifications
| Model | Airtac TCL Triple Axis Cylinder TCL12X40-S |
|---|---|
| Series | TCL JIS guided (twin-rod) cylinder |
| Bore size | Ø12 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Bearing | Steel-ball linear bearing |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.08° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 150 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø12mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 57 N | 42 N |
| 0.7 MPa | 79 N | — |
| Max | 12 kgf | |
Force is set by the bore and piston rod (Ø6 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCL Triple Axis Cylinder TCL12X40-S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| L | Bearing: Steel-ball linear bearing (L = linear ball). |
| 12 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCM12X40 (brass sliding bearing, more impact/dust tolerant). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCL Triple Axis Cylinder TCL12X40-S Is Used
Lab Sample Handling
Provides 57 N of precise vertical lift for sample racks. The steel-ball linear bearing ensures smooth travel without stick-slip, while the ±0.08° non-rotating tolerance keeps test trays level.
Small Component Pick-and-Place
Moves light electronic parts using an off-centre gripper. The twin guide rods support the moment load, and the Ø6 mm rod handles 79 N of thrust at 0.7 MPa without external guidance.
3D Printer Bed Levelling
Actuates a calibration probe with high precision. The integrated JIS guided body saves space, and the four sensor slots accept CS1 reed or DS1 electronic switches for exact position feedback.
Is the Airtac TCL Triple Axis Cylinder TCL12X40-S the Right Cylinder?
If sizing up or down, the neighbouring Ø16 bore yields 101 N of push at 0.5 MPa for heavier jobs, while this Ø12 model provides 57 N for lighter tasks. Choose the sister TCM series with its brass sliding bearing if your application involves severe impact or dusty radial loads. To replace this unit, specify bore 12, stroke 40, PT thread, and the standard S magnet.
Note that the guide resists rotation, not gravity; if air pressure drops, the rod drifts. For fail-safe position holding, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCL Triple Axis Cylinder TCL12X40-S FAQ
At 0.5 MPa, it generates 57 N of push and 42 N of pull. At 0.7 MPa, the push increases to 79 N. The theoretical maximum force is 12 kgf at 1.0 MPa.
The TCL uses a steel-ball linear bearing for low-friction, high-precision travel, making it ideal for vertical lifts. The TCM uses a brass sliding bearing better suited for impact or dusty radial-load duty. The TCL has fixed TPU bumpers at each end rather than an adjustable air cushion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCL Cylinders
Request a Quote for Airtac TCL Triple Axis Cylinder TCL12X40-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.