Airtac TCL Triple Axis Cylinder TCL16X20-S
The AirTAC Airtac TCL Triple Axis Cylinder TCL16X20-S is a genuine JIS-standard guided cylinder with a Ø16mm bore and 20mm stroke on twin guide rods. Its integrated steel-ball linear bearing gives low-friction, high-precision travel — well suited to vertical lifts and high-load, high-accuracy moves, holding the tool square to ±0.07° of rotation without any external linear guide.
- BoreØ16 mm
- Stroke20 mm
- Port sizeM5×0.8
- BearingSteel-ball linear bearing
- Non-rotating±0.07°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCL Triple Axis Cylinder TCL16X20-S
The AirTAC TCL16X20-S is a JIS-standard twin-rod guided cylinder featuring a steel-ball linear bearing for low-friction, high-precision motion. A central drive piston runs between two guide rods in a single integrated body, eliminating the need for an external linear slide. Generating 101 N of push at 0.5 MPa, this double-acting unit is built for compact lifting and transfer tasks.
It delivers a non-rotating accuracy of ±0.07°, keeping a gripper or blade square under off-centre loads. The Ø8 mm piston rod and M5x0.8 ports make plumbing straightforward, while the integrated magnet works with CS1 reed or DS1 electronic switches across four sensor slots. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion.
Airtac TCL Triple Axis Cylinder TCL16X20-S Technical Specifications
| Model | Airtac TCL Triple Axis Cylinder TCL16X20-S |
|---|---|
| Series | TCL JIS guided (twin-rod) cylinder |
| Bore size | Ø16 mm |
| Stroke | 20 mm |
| Acting type | Double acting |
| Bearing | Steel-ball linear bearing |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.07° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 200 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 75 N |
| 0.7 MPa | 141 N | — |
| Max | 21 kgf | |
Force is set by the bore and piston rod (Ø8 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCL Triple Axis Cylinder TCL16X20-S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| L | Bearing: Steel-ball linear bearing (L = linear ball). |
| 16 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCM16X20 (brass sliding bearing, more impact/dust tolerant). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCL Triple Axis Cylinder TCL16X20-S Is Used
PCB Panel Lift
Uses the 101 N thrust and low-friction steel-ball bearing to raise delicate circuit boards smoothly without stick-slip on vertical travel.
Off-Centre Gripper Transfer
The ±0.07° non-rotating tolerance keeps a small parts gripper perfectly square during lateral moves, resisting twisting moments.
Lab Sample Positioning
Ideal for precise short-stroke routing of test tubes, relying on the integrated twin-rod guide so no separate rail is required.
Is the Airtac TCL Triple Axis Cylinder TCL16X20-S the Right Cylinder?
This 16 mm bore provides 101 N push and 75 N pull at 0.5 MPa. If you need less force, step down to the Ø12 bore which gives roughly 57 N of thrust; if your application demands more power, the Ø20 bore yields about 157 N. For environments with heavy impact or dusty radial loads, consider the TCM16 with its brass sliding bearing instead of this linear ball unit. To replace this cylinder, match the 16 mm bore, 20 mm stroke, M5x0.8 PT ports, and the standard S magnet.
Note that the guide resists rotation but will not hold a load vertically if air pressure is lost or the valve is centred—the rod will drift. For a fail-safe hold, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCL Triple Axis Cylinder TCL16X20-S FAQ
At 0.5 MPa it provides 101 N push and 75 N pull. At 0.7 MPa the push increases to 141 N, with a theoretical maximum force of 21 kgf. The operating speed range is 30-500 mm/s.
No, each end lands on a fixed TPU bumper to soften the stop. There is no air-cushion screw to set on the TC series. The standard built-in magnet supports CS1 reed and DS1 electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCL Cylinders
Request a Quote for Airtac TCL Triple Axis Cylinder TCL16X20-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.