Airtac TCL Triple Axis Cylinder TCL16X60-S
The AirTAC Airtac TCL Triple Axis Cylinder TCL16X60-S is a genuine JIS-standard guided cylinder with a Ø16mm bore and 60mm stroke on twin guide rods. Its integrated steel-ball linear bearing gives low-friction, high-precision travel — well suited to vertical lifts and high-load, high-accuracy moves, holding the tool square to ±0.07° of rotation without any external linear guide.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- BearingSteel-ball linear bearing
- Non-rotating±0.07°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCL Triple Axis Cylinder TCL16X60-S
The AirTAC TCL16X60-S is a JIS-standard twin-rod guided cylinder featuring a low-friction steel-ball linear bearing. It integrates the drive piston and two guide rods into one body, eliminating the need for an external linear slide. Delivering 101 N of push at 0.5 MPa, this double-acting unit handles off-centre loads with a ±0.07° non-rotating tolerance, keeping grippers square during travel.
The Ø8 mm piston rod and M5x0.8 ports make it a compact fit for tight assemblies. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion. Air feeds via upper or side port groups, while four sensor slots accept CS1 reed or DS1 electronic switches to track position from any face.
Airtac TCL Triple Axis Cylinder TCL16X60-S Technical Specifications
| Model | Airtac TCL Triple Axis Cylinder TCL16X60-S |
|---|---|
| Series | TCL JIS guided (twin-rod) cylinder |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Bearing | Steel-ball linear bearing |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.07° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 200 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 75 N |
| 0.7 MPa | 141 N | — |
| Max | 21 kgf | |
Force is set by the bore and piston rod (Ø8 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCL Triple Axis Cylinder TCL16X60-S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| L | Bearing: Steel-ball linear bearing (L = linear ball). |
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCM16X60 (brass sliding bearing, more impact/dust tolerant). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCL Triple Axis Cylinder TCL16X60-S Is Used
PCB Handling Lift
Raises delicate electronics on a smooth vertical path without stick-slip, using 101 N of thrust to elevate a carrier plate precisely.
3D Printer Carriage Shift
Transfers an off-centre print head bracket with ±0.07° anti-rotation accuracy, ensuring the tool stays square during rapid positioning.
Lab Sample Indexing
Stops and positions a moving sample tray using the integrated twin guide rods, absorbing side torque without requiring a separate rail.
Is the Airtac TCL Triple Axis Cylinder TCL16X60-S the Right Cylinder?
Select this 16 mm bore when your application requires 101 N of thrust at 0.5 MPa across a 60 mm stroke. If you need less force, the Ø12 bore provides about 57 N; stepping up to the Ø20 bore yields roughly 157 N. Consider the sibling TCM series with its brass sliding bearing if your duty cycle involves heavy impacts or dusty radial loads. To replace this unit, match the 16 mm bore, 60 mm stroke, M5x0.8 PT ports, and standard S magnet.
Note that this guide resists rotation but does not hold a load vertically if air pressure drops. The rod will drift downward under gravity upon air loss. For a fail-safe hold, install an external rod lock or a pilot-operated check valve in your circuit.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCL Triple Axis Cylinder TCL16X60-S FAQ
At 0.5 MPa it provides 101 N push and 75 N pull; at 0.7 MPa push increases to 141 N. The theoretical maximum force is 21 kgf, and the operating speed ranges from 30-500 mm/s.
No, there is no adjustable air cushion. Each end lands on a fixed TPU bumper to soften the impact. The standard built-in magnet works with CS1 reed and DS1 electronic switches in the four body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCL Cylinders
Request a Quote for Airtac TCL Triple Axis Cylinder TCL16X60-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.