Airtac TCL Triple Axis Cylinder TCL63X75S
The AirTAC Airtac TCL Triple Axis Cylinder TCL63X75S is a genuine JIS-standard guided cylinder with a Ø63mm bore and 75mm stroke on twin guide rods. Its integrated steel-ball linear bearing gives low-friction, high-precision travel — well suited to vertical lifts and high-load, high-accuracy moves, holding the tool square to ±0.04° of rotation without any external linear guide.
- BoreØ63 mm
- Stroke75 mm
- Port size1/4"
- BearingSteel-ball linear bearing
- Non-rotating±0.04°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCL Triple Axis Cylinder TCL63X75S
The AirTAC TCL63X75S is a JIS guided twin-rod double-acting cylinder integrating a steel-ball linear bearing. It delivers 1559 N of push force and 1402 N of pull force at 0.5 MPa, making it suited for heavy-duty positioning tasks. The integrated twin guide rods eliminate the need to align a separate external slide, saving engineering hours. A non-rotating tolerance of ±0.04° ensures your end-effector stays square under off-centre loads.
This 63 mm bore unit runs on a Ø20 mm piston rod and features 1/4" ports. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion. The standard built-in magnet allows positioning feedback via CS1 reed or DS1 electronic switches in the four sensor slots.
Airtac TCL Triple Axis Cylinder TCL63X75S Technical Specifications
| Model | Airtac TCL Triple Axis Cylinder TCL63X75S |
|---|---|
| Series | TCL JIS guided (twin-rod) cylinder |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Bearing | Steel-ball linear bearing |
| Port size | 1/4" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.04° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max | 318 kgf | |
Force is set by the bore and piston rod (Ø20 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCL Triple Axis Cylinder TCL63X75S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| L | Bearing: Steel-ball linear bearing (L = linear ball). |
| 63 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCM63X75 (brass sliding bearing, more impact/dust tolerant). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCL Triple Axis Cylinder TCL63X75S Is Used
Heavy Pallet Gate Stop
Halts moving pallets on a conveyor using 1559 N of thrust at 0.5 MPa; the steel-ball linear bearing absorbs the radial impact without stick-slip.
Welding Fixture Actuation
Positions heavy welding clamps smoothly with a ±0.04° non-rotating tolerance, keeping the fixture square during off-centre load shifts.
Vertical Press Descender
Lowers a 318 kgf rated press head smoothly using low-friction linear bearings, preventing sudden drops on high-cycle vertical lifts.
Is the Airtac TCL Triple Axis Cylinder TCL63X75S the Right Cylinder?
When sizing this model, consider stepping to the adjacent bores: the Ø50 variant provides about 982 N of push at 0.5 MPa, while the Ø80 option yields roughly 2513 N. Choose the sibling TCM series if your application involves severe impact or dusty radial loads, as its brass sliding bearing handles those abuses better than the steel-ball linear bearing. Remember that a TC cylinder does not hold its load if air pressure drops or the valve is centred; the rod will drift. For a fail-safe hold, install an external rod lock or a pilot-operated check valve. Replacement requires matching the 63 mm bore, 75 mm stroke, 1/4" PT ports, and the standard S magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCL Triple Axis Cylinder TCL63X75S FAQ
At 0.5 MPa it generates 1559 N of push and 1402 N of pull. At 0.7 MPa the push increases to 2182 N. The theoretical maximum force is 318 kgf at 1.0 MPa.
No, it uses a fixed rubber TPU bumper at each end to soften the stop. There is no air-cushion screw to set. The standard built-in magnet works with CS1 reed and DS1 electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCL Cylinders
Request a Quote for Airtac TCL Triple Axis Cylinder TCL63X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.