Airtac TCM Triple Axis Cylinder TCM32X75-S
The AirTAC Airtac TCM Triple Axis Cylinder TCM32X75-S is a genuine JIS-standard guided cylinder with a Ø32mm bore and 75mm stroke on twin guide rods. Its integrated brass sliding bearing gives high radial-load and impact resistance — about double the horizontal impact tolerance of a plain cylinder, holding the tool square to ±0.06° of rotation without any external linear guide.
- BoreØ32 mm
- Stroke75 mm
- Port size1/8"
- BearingBrass sliding bearing
- Non-rotating±0.06°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCM Triple Axis Cylinder TCM32X75-S
The AirTAC TCM32X75-S is a JIS-standard twin-rod guided cylinder featuring a robust brass sliding bearing. A central drive piston runs between two guide rods in a single integrated body, actively preventing rotation and absorbing side load so you can skip installing an external linear rail. This 32 mm bore unit generates 402 N of push and 302 N of pull at 0.5 MPa, making it well-suited for mid-range transfer and gating tasks over its 75 mm stroke.
Because it uses a brass sliding bearing rather than a steel-ball guide, this model shrugs off dust, weld spatter, and hard knocks—delivering roughly double the horizontal impact resistance of a plain cylinder. It holds a tight ±0.06° non-rotating tolerance, keeping an off-centre gripper or blade perfectly square under eccentric loads. The integrated body offers two independent port groups (upper face and side) on 1/8" threads, allowing flexible plumbing without extra elbows. Stroke terminations are damped by fixed TPU bumpers, meaning there is no air-cushion screw to adjust.
Airtac TCM Triple Axis Cylinder TCM32X75-S Technical Specifications
| Model | Airtac TCM Triple Axis Cylinder TCM32X75-S |
|---|---|
| Series | TCM JIS guided (twin-rod) cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Bearing | Brass sliding bearing |
| Port size | 1/8" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.06° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max | 82 kgf | |
Force is set by the bore and piston rod (Ø16 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCM Triple Axis Cylinder TCM32X75-S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| M | Bearing: Brass sliding bearing (M = brass sliding). |
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCL32X75 (steel-ball linear bearing, lower friction & higher precision). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCM Triple Axis Cylinder TCM32X75-S Is Used
Pallet Stop Gate
Halting heavy pallets on a dusty transfer line is easy with the 402 N push force. The brass sliding bearing tolerates abrasive grit where a steel-ball guide would jam or wear prematurely.
Off-Centre Gripper Slide
Picking an asymmetric part keeps the tool square thanks to the ±0.06° non-rotating tolerance. The twin guide rods carry the eccentric moment without needing a separate rail.
Weld Cell Clamp
Resisting weld spatter and coolant spray, the brass bearing provides the robust radial-load capacity needed for clamping fixtures. The 1/8" side ports simplify plumbing in tight cell layouts.
Is the Airtac TCM Triple Axis Cylinder TCM32X75-S the Right Cylinder?
When sizing this model, consider its neighbours in the AirTAC range: stepping down to a Ø25 bore yields about 245 N of push at 0.5 MPa, while moving up to a Ø40 bore provides 628 N. If your task demands low-friction precision or carries heavy vertical loads rather than surviving dirty impacts, choose the sister TCL series with its steel-ball linear bearing instead of this brass-slide variant. To replace this unit exactly, specify bore 32, stroke 75, 1/8" ports, PT thread form, and the standard built-in S magnet. Note that a guided cylinder will not hold a load in place if air pressure drops or the valve is centred; the rod will drift, so fit an external rod lock or pilot-operated check valve for fail-safe positioning.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCM Triple Axis Cylinder TCM32X75-S FAQ
At 0.5 MPa it delivers 402 N of push and 302 N of pull. At the maximum 0.7 MPa, push increases to 563 N, with a theoretical maximum force of 82 kgf. The twin guide rods hold a non-rotating tolerance of ±0.06°.
There is no adjustable air cushion; each end relies on a fixed rubber TPU bumper to soften the stop. The cylinder ships with a standard built-in magnet (S) and has four sensor slots that accept AirTAC CS1 reed or DS1 electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCM Cylinders
Request a Quote for Airtac TCM Triple Axis Cylinder TCM32X75-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.