The AirTAC GC30015MLF2WG AirTAC F.R.L. Combination G1/2, 5 um is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/2" ports, a 5 µm element, a manual drain and regulates 0.05 - 0.9 MPa (7 - 130 psi).
The GC30015MLF2WG is an AirTAC GC-series three-unit F.R.L. combination: a separate filter, regulator and lubricator assembled as one air-preparation set for a compressed-air line. This size-300 unit has a G1/2 (BSPP) port, a 5 um filter element (code W), a manual drain on the filter bowl, and the low-pressure-type regulator. The embedded square gauge is fitted and reads in psi, the polycarbonate bowls let you see condensate and oil level at a glance, a mounting bracket is included, and the set is rated for a maximum inlet pressure of 1.0 MPa (145 psi) at -5 to 70 C (non-freezing).
This is a genuine AirTAC part. The GC series is available in sizes 200, 300, 400 and 600 with ports from 1/8 to 1 inch, a choice of PT, G (BSPP) or NPT thread, automatic, manual or differential-pressure drains, 40 um standard or 5 um filtration, and gauge scales in MPa, psi or bar. Flow is published as curves rather than a single rated figure, so ask us to confirm sizing and any datasheet figure against your application before ordering.
| Model | GC30015MLF2WG AirTAC F.R.L. Combination G1/2, 5 um |
|---|---|
| Series | GC300 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/2" (G (BSPP) thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Manual drain |
| Bowl material | PC |
| Pressure gauge | Fitted — square, psi scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC300 | G-series F.R.L. combination, 300 body — sets the port range. |
|---|---|
| 15 | Port size PT1/2". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| M | Drain: Manual drain — this also sets the regulating band (0.05 - 0.9 MPa (7 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| G | G (BSPP) thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF300-15 filter, GR300-15 regulator and GL300-15 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC300 · PT1/2" · 5 µm |
|---|---|
| One size down | GC200 |
| One size up | GC400 |
| Two-unit equivalent | GFC300-15 |
| Build order | Filter → regulator → lubricator |
Conditioning the compressed-air feed to gripper cylinders and small actuators on a pick-and-place robot: the 5 um element strips water and particulate, the regulator holds the circuit setting, and the lubricator mists oil downstream to the actuators.
Supplying filtered, regulated and lubricated air to the cylinders and air valves on a carton-forming and sealing conveyor, with the manual-drain filter bowl emptied as part of routine line housekeeping.
Feeding an assembly-line circuit that runs at a set point well below full line pressure, where the low-pressure-type regulator is the appropriate choice; the square psi gauge gives a direct readout of the set pressure.
Within the GC range the real choices are: size and port (200/300/400/600, 1/8 to 1 inch) stepped against the air demand of the line; drain type on the filter (automatic, manual or differential-pressure); filter grade (40 um standard, 5 um with code W - this unit carries the 5 um element); gauge scale (MPa, psi or bar); and thread (PT standard, with G and NPT as order options). This configuration is the low-pressure regulator type with a manual drain, a psi-scale square gauge and an included mounting bracket. Because flow is published as curves rather than a single rating, ask us to confirm sizing against your application before ordering.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR300-15 regulator with a GF300-15 filter on that branch.
AirTAC publishes flow for the GC series as curves, not as a single rated figure, so we do not quote a number here. Tell us your working pressure and air demand and we will confirm the sizing from the datasheet on request.
The L in GC30015MLF2WG marks the low-pressure regulator type rather than the standard one. The exact adjustment range for this type is not published in the material we hold, so ask us to confirm the range against your set pressure before ordering.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.