The AirTAC GC60025ALC2 AirTAC F.R.L. Combination, PT1 (1 in) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1" ports, a 40 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
The GC60025ALC2 is an AirTAC GC600 three-unit F.R.L. combination: a separate air filter, pressure regulator and oil-mist lubricator assembled as one set. The filter removes water and particulate down to the standard 40 um grade, the regulator sets downstream pressure, and the lubricator meters oil mist into the air line. This configuration is built for 1 in PT ports, uses the low-pressure regulator type, and carries an automatic drain on the filter bowl so condensate is ejected without manual attention. At size 600 the bowls are aluminium alloy, and the set includes a round pressure gauge reading in psi. No reverse/check valve is fitted.
This is a genuine AirTAC part. The GC series is available in sizes 200, 300, 400 and 600, with port options from 1/8 in to 1 in, PT as the standard thread and G (BSPP) or NPT as order options, a choice of differential-pressure, automatic or manual drain, 40 um or 5 um (W) filter grade, gauge scale in MPa, psi or bar, and an optional reverse/check valve (K). Maximum working (inlet) pressure is 1.0 MPa (145 psi) and the operating temperature range is -5 to 70 C, non-freezing. Flow is published as curves rather than a single rated figure, so ask us to confirm sizing and any datasheet figure against your application before ordering.
| Model | GC60025ALC2 AirTAC F.R.L. Combination, PT1 (1 in) |
|---|---|
| Series | GC600 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1" (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | Aluminium alloy |
| Pressure gauge | Fitted — round, psi scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC600 | G-series F.R.L. combination, 600 body — sets the port range. |
|---|---|
| 25 | Port size PT1". This body offers 20 = PT3/4", 25 = PT1". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| C | Gauge shape: Round. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF600-25 filter, GR600-25 regulator and GL600-25 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC600 · PT1" · 40 µm |
|---|---|
| One size down | GC400 |
| Two-unit equivalent | GFC600-25 |
| Build order | Filter → regulator → lubricator |
Feeds filtered, regulated and lubricated air to spray booths and air-driven applicators on a paint line, with the automatic drain clearing condensate between shifts without operator attention.
Supplies the main air drop to clamps and pneumatic presses in a casting plant, where the low-pressure regulator type matches circuits that run at reduced line pressure and the lubricator keeps cylinder seals working.
Conditions the air feeding conveyor gate cylinders and diverters on a bottling line, with 40 um filtration protecting valves and the round psi gauge giving operators a local pressure readout.
Start with the port and size step: this unit is size 600 with 1 in PT ports, the largest step in the GC range (200/300/400/600), so match it to the line size and the flow your system needs - larger sizes carry more flow. The drain here is automatic, which suits unattended installations; differential-pressure (default) and manual drains are the alternatives. The filter grade is the standard 40 um; specify the W code if the application needs 5 um. The gauge is the external round type reading in psi; embedded square gauges and MPa or bar scales are the other choices. Thread is PT as standard, with G (BSPP) and NPT available to order. Note that this is the low-pressure regulator type (L); its exact adjustment range is not published, so confirm it with us. Flow is published as curves, not a single rating, so ask us to confirm sizing against the application before ordering.
Quick checklist
The aluminium-alloy bowls on the GC600 suit harsher environments than PC bowls. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR600-25 regulator with a GF600-25 filter on that branch.
AirTAC publishes flow for the GC series as curves, not as a single rated figure, so we do not quote a rated flow, Cv or SCFM number. Tell us your line size and application and we will confirm the flow figures from the datasheet on request before you order.
The L marks the low-pressure regulator type, and its exact adjustment range is not published, so confirm it with us for your circuit. The A marks an automatic drain on the filter bowl, which ejects collected condensate on its own instead of relying on the differential-pressure (default) or manual drain options.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.