The AirTAC GC60025LF2WG AirTAC F.R.L. Combination, G1 (1 in) Port is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1" ports, a 5 µm element, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
The AirTAC GC series is a three-piece F.R.L. combination: a separate air filter, pressure regulator and lubricator assembled as one prepared-air station that cleans, regulates and oil-mist lubricates the compressed air in a single installation. This GC600 configuration is the size 600 frame with a G1 (1 in) port in G (BSPP) thread, built as the low-pressure (L) regulator type. It carries the 5 um filter element (code W), the differential-pressure drain on the filter bowl, an embedded square gauge reading in psi, and the mounting bracket is included. No reverse/check valve is fitted, and the size 600 bowls are aluminium alloy.
This is a genuine AirTAC part. The GC family spans sizes 200, 300, 400 and 600, with port sizes from 1/8 in to 1 in, a choice of differential-pressure, automatic or manual drain, 40 um standard or 5 um (W) filtration, square or round gauges scaled in MPa, psi or bar, and PT, G or NPT threads. Maximum working pressure is 1.0 MPa (145 psi) and the operating temperature range is -5 to 70 C, non-freezing. Rated flow is published as curves rather than a single figure, so ask us to confirm the datasheet and sizing for your application.
| Model | GC60025LF2WG AirTAC F.R.L. Combination, G1 (1 in) Port |
|---|---|
| Series | GC600 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1" (G (BSPP) thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | Aluminium alloy |
| Pressure gauge | Fitted — square, psi scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC600 | G-series F.R.L. combination, 600 body — sets the port range. |
|---|---|
| 25 | Port size PT1". This body offers 20 = PT3/4", 25 = PT1". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| G | G (BSPP) thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF600-25 filter, GR600-25 regulator and GL600-25 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC600 · PT1" · 5 µm |
|---|---|
| One size down | GC400 |
| Two-unit equivalent | GFC600-25 |
| Build order | Filter → regulator → lubricator |
Press and clamp cylinders on a fabrication cell need air that is dry, held at a stable set pressure and lightly oiled for seal life. This unit filters water and swarf from the shop air, regulates the clamp circuit at the pressure the tooling was set up for, and meters oil mist to the cylinders - all from one G1 connection at the cell drop.
Impact wrenches, nutrunners and riveters on an assembly floor run best off a prepared-air point that conditions the supply before the hose reels. Mounted at the station, this combination removes condensate and 5 um particles, holds the regulator setting for consistent tool torque behaviour, and feeds oil mist downstream to keep the tools lubricated through the shift.
Bottle palletizers and case packers use large-bore cylinders that cycle continuously in a humid environment. A size 600 F.R.L. at the machine inlet strips water carried over from the plant ring main, keeps the supply pressure steady so layer patterns stay repeatable, and delivers a fine oil mist to the cylinder and valve seals.
Choose the size step first: 200, 300, 400 or 600 sets the port (here 600 with a 1 in G1 port in G thread) and should be matched to the airflow your line needs - we can check the published flow curves against your demand before you order. Then set the options: drain type (differential-pressure as here, automatic, or manual), filter grade (40 um standard or 5 um with the W code, as fitted here), gauge style and scale (this unit has the embedded square gauge in psi; an external round gauge is optional), thread family (PT is the standard; G and NPT are order options), and bracket. Note this is the low-pressure (L) regulator type; we confirm its adjustment range on request rather than quoting the standard-type figures. If you need single functions, GF, GR and GL cover filter, regulator or lubricator alone, GFR combines filter and regulator in one body, and GFC pairs a filter-regulator with a lubricator.
Quick checklist
The aluminium-alloy bowls on the GC600 suit harsher environments than PC bowls. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR600-25 regulator with a GF600-25 filter on that branch.
Flow for the GC series is published as curves, not as a single rated figure, so we do not quote a number here. Send us your port size, working pressure and air demand, and we will confirm the datasheet flow figures for GC60025LF2WG on request before you order.
The differential-pressure drain is the catalogue default for the filter bowl on this configuration - it is the drain type fitted when no A or M code appears in the model. If your application suits it better, an automatic drain (code A) or a manual drain (code M) can be ordered on the same GC600 frame; just tell us which you want when ordering.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.