The AirTAC GC60025LF2WK AirTAC Three-Unit F.R.L., PT1 (1 in) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1" ports, a 5 µm element, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
The GC60025LF2WK is an AirTAC GC-series three-unit F.R.L. combination: a separate filter, regulator and lubricator assembled as one air-preparation set. This size 600 unit is built for 1 in PT threads and carries the W-grade 5 um filter element with a differential-pressure drain on the filter bowl, a low-pressure regulator fitted with an embedded square psi gauge, and a reverse/check valve. Maximum inlet pressure is 1.0 MPa (145 psi), operating temperature is -5 to 70 C (non-freezing), and because this is the 600 size the bowls are aluminium alloy.
This is a genuine AirTAC part. The GC series spans sizes 200, 300, 400 and 600 with port options from 1/8 in to 1 in, plus drain, filter-grade, gauge-scale, thread (PT standard, with G and NPT orderable) and bracket choices; a mounting bracket is included with this unit. Flow for the series is published as curves rather than a single rated figure, so ask us to confirm the datasheet numbers for your application before ordering.
| Model | GC60025LF2WK AirTAC Three-Unit F.R.L., PT1 (1 in) |
|---|---|
| Series | GC600 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1" (PT thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | Aluminium alloy |
| Pressure gauge | Fitted — square, psi scale |
| Reflux valve | Fitted (reverse flow permitted) |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC600 | G-series F.R.L. combination, 600 body — sets the port range. |
|---|---|
| 25 | Port size PT1". This body offers 20 = PT3/4", 25 = PT1". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| K | Reverse-flow (reflux) valve fitted. |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF600-25 filter, GR600-25 regulator and GL600-25 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC600 · PT1" · 5 µm |
|---|---|
| One size down | GC400 |
| Two-unit equivalent | GFC600-25 |
| Build order | Filter → regulator → lubricator |
Feeds spray booths and paint guns from a plant air main, filtering water and fine particulate, holding a low set pressure and metering oil mist so finish equipment runs clean and sealed.
Supplies the clamping fixture circuit on a machining centre: 5 um filtration protects the clamp valves, the low-pressure regulator holds a gentle holding force, and the check valve keeps the circuit from venting back.
Prepares air for the flap-fold and taping cylinders on a case-packing conveyor, with regulated pressure for consistent stroke speed and oil mist to keep the cylinders lubricated through long shifts.
Step through the GC sizes (200/300/400/600) to match the port and the air demand of your line; this unit is the 600 size with 1 in PT threads. The filter here is the 5 um W grade rather than the 40 um standard - choose 5 um where downstream valves and cylinders need finer particulate removal. The drain is differential-pressure (the family default); automatic and manual drains are orderable alternatives. The gauge is the embedded square type reading in psi, with external round gauges and MPa or bar scales available as options. Thread is PT as standard, with G (BSPP) and NPT orderable, and the mounting bracket is included.
Flow for the GC series is published as curves, not a single rated number, so send us your pressure and air-demand figures and we will confirm sizing against the datasheet before you order.
Quick checklist
The aluminium-alloy bowls on the GC600 suit harsher environments than PC bowls. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR600-25 regulator with a GF600-25 filter on that branch.
AirTAC publishes flow for the GC series as curves rather than a single rated figure, so we do not quote one number here. Tell us your working pressure and air demand and we will confirm the flow from the datasheet for this 600-size, 1 in PT unit before you order.
The L in the code marks the low-pressure regulator variant, and AirTAC does not publish its exact adjustment range on the standard sheet. If your circuit runs below the standard range, send us your set pressure and we will confirm suitability from the datasheet. The rest of this decode is standard: 5 um W-grade filter, square psi gauge, differential-pressure drain and a fitted reverse/check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.