The AirTAC GFR20006MLJF2T AirTAC Filter Regulator NPT1/8 Low-Pressure is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has PT1/8" ports, a manual drain and regulates 0.05 - 0.9 MPa (7 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
The GFR20006MLJF2T is an AirTAC GFR200 filter regulator: a water-and-particulate filter and a pressure regulator built into one body, so a single compact unit cleans the compressed air and holds your set pressure downstream. This configuration is the size 200 unit with a 1/8 in NPT port, a polycarbonate bowl with manual drain, a 40 um filter element, the low-pressure regulator type, and an embedded square gauge reading in psi. No mounting bracket is fitted and no reverse/check valve is included.
It is a genuine AirTAC part. The GFR series spans sizes 200, 300, 400 and 600 with ports from 1/8 in up to 1 in, and options include automatic or differential-pressure drains, a 5 um element (code W), G (BSPP) or NPT threads in place of the PT standard, and gauge scale choices. Maximum inlet pressure is 1.0 MPa (145 psi) and the working temperature range is -5 to 70 C (non-freezing). Because flow is published as curves rather than a single rating, we confirm the datasheet and sizing figures on request.
| Model | GFR20006MLJF2T AirTAC Filter Regulator NPT1/8 Low-Pressure |
|---|---|
| Series | GFR200 filter regulator |
| Port size | PT1/8" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Low-pressure type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Manual drain |
| Bowl material | PC |
| Pressure gauge | Fitted — square, psi scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| M | Drain: Manual drain — this also sets the regulating band (0.05 - 0.9 MPa (7 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| J | Supplied without bracket. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · PT1/8" · 40 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-06 (two-unit set) |
Packaging machines often run small glue, ink or label-apply cylinders at gentle settings. A size 200 filter regulator with a manual-drain bowl and a psi gauge lets an operator clean the air, read the set point at a glance and bleed accumulated water during changeover.
Light pneumatic clamps and swing cylinders at an assembly workstation need clean, steady air at a modest set pressure. This compact filter regulator conditions the supply at the bench, with the square psi gauge giving the operator direct visual feedback.
Laboratory and pilot rigs driving small air actuators benefit from filtration plus regulation in one body, especially where set pressures are low. The manual drain suits rigs that are checked daily, and the psi gauge supports documented test setups.
The real choices are all decodable from the code. The size 200 / 1/8 in port step sits at the low end of the GFR flow span, so match it against your downstream air consumption before ordering. The manual drain (code M) means the bowl is bled by hand on a schedule - choose the automatic drain if the unit sits where nobody visits. The 40 um element is the standard grade; specify W for 5 um where finer pre-filtration matters. The square gauge on this unit reads psi; MPa and bar scales are available and an external round gauge is optional. Thread here is NPT; PT is the catalogue standard and G (BSPP) is orderable. Bracket: not fitted (code J). Flow is published as curves, not a single rated figure, so ask us to confirm sizing against your application before you order.
Quick checklist
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC publishes flow for the GFR series as curves rather than a single rated figure, so we do not quote a number here. Send us your line pressure, set pressure and downstream air consumption, and we will confirm the datasheet curve and sizing for this 1/8 in unit on request.
The M in the code sets the polycarbonate bowl to manual draining, which suits units that are inspected regularly. The same GFR200 body is available with an automatic drain (code A) or the differential-pressure drain (blank) if you would rather not rely on manual bleeding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.