Airtac MIC Cushioned Mini Cylinder MIC25X125CM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X125CM is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 125mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke125 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X125CM
Dial in end-of-stroke deceleration with the AirTAC MIC25X125CM, a double-acting round-body mini cylinder built around a stainless-steel barrel and piston rod. The CM round rear cover keeps the port orientation clean for tight assemblies. Because this is the adjustable-cushion variant, a needle valve at both ends absorbs high-speed kinetic energy, protecting your payload far better than a fixed rubber bumper.
At the Ø25 bore class, the 1/8" port feeds a 10mm piston rod delivering 245.3 N of push force at 0.5 MPa. That translates to a safe working load of roughly 147 N, letting you lift about 12.5 kg vertically with a 2:1 safety margin. This SKU lacks the -S magnet, so it cannot host CMSG, DMSG or EMSG sensors. It conforms to the ISO 6432 mounting interface for straightforward bracket interchange.
Airtac MIC Cushioned Mini Cylinder MIC25X125CM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X125CM |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 125 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X125CM
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X125CM Is Used
Package Diverting
At 245 N of push force, this cylinder cleanly knocks 12 kg cartons off a high-speed belt without the harsh impact a bumper would cause.
Light Pressing
The adjustable needle cushion allows precise, low-noise pressing of lightweight bearings or pins at rapid cycle rates.
Gate Actuation
Its stainless round-body construction resists mild washdown humidity while smoothly operating 125mm stroke sorting gates.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X125CM the Right Cylinder?
When sizing this 125mm stroke unit against adjacent bores, stepping down to the Ø20 MIC drops the 0.5 MPa push force to 157 N, while moving up to the Ø32 MIC raises it to 402 N. Choose this Ø25 model when your cycle speed sits in the upper range and the adjustable air cushion is required to prevent harsh end-stroke slamming. Note that the cushion only decelerates the load; it does not function as a brake. If the air supply drops, the rod will drift. To hold a load securely during a pressure loss, fit an external rod lock or a pilot-operated check valve. Mount this non-magnetic CM-cover version using standard ISO 6432 foot or flange hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X125CM FAQ
This Ø25 mm bore cylinder features a 1/8" port and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, 343.4 N push and 288.5 N pull at 0.7 MPa, with a theoretical maximum force of 50 kgf at 1.0 MPa.
No, this specific SKU lacks the internal magnet. You must select the -S variant to mount CMSG, DMSG or EMSG magnetic switches. The adjustable air cushion at both ends only controls deceleration and does not lock the rod in place.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X125CM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.