Airtac MIC Cushioned Mini Cylinder MIC25X135CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X135CA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 135mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke135 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X135CA
Tuned for high-speed cycling, the AirTAC MIC25X135CA uses a needle-set variable air cushion at both ends to decelerate the load smoothly, eliminating the end-of-stroke bang typical of bumper mini cylinders. This double-acting stainless steel round-body actuator provides a 245.3 N push and 206.1 N pull at 0.5 MPa, yielding a safe working load of roughly 147 N or a 12.5 kg vertical lift with a 2:1 margin.
The Ø25 mm bore aligns with the ISO 6432 mounting interface, dropping directly into standard mini-cylinder brackets and clevises. Its stainless barrel and rod resist mild corrosion and washdown environments. This specific CA rear-cover configuration adds a pivot clevis for articulated mounting. Note that this SKU lacks the -S magnet, so it cannot accept CMSG, DMSG or EMSG sensors.
Airtac MIC Cushioned Mini Cylinder MIC25X135CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X135CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 135 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X135CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×135 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X135CA Is Used
Package Diverting
Pushes lightweight cartons off a high-speed belt using its 245.3 N thrust, relying on the adjustable cushion to stop the stroke quietly without slamming the frame.
Film Sealing Head
Drives a sealing jaw up to 135 mm with smooth deceleration, preventing jaw bounce and protecting the heat element from high-cycle shock damage.
Pallet Tag Applicator
Extends a label applicator onto pallets in damp staging areas; the stainless construction handles ambient moisture while the CA clevis allows angular alignment.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X135CA the Right Cylinder?
If 245.3 N of push is excessive, the smaller Ø20 bore offers 157.0 N at 0.5 MPa; if your payload requires more muscle, stepping up to the Ø32 provides 402.2 N. The adjustable cushion is essential when driving heavier masses at high speeds, as it protects the mechanism by absorbing kinetic energy without acting as a locking brake. For position holding on air loss, fit an external rod lock or pilot check valve, since the piston will drift.
The 1/8 inch port and M10x1.25 male rod thread match standard Ø25 mini-cylinder hardware. Because this is a non-magnet SKU, sensing is impossible; order the -S variant if you need to mount CMSG, DMSG or EMSG switches. Alongside the CA clevis, you can adapt the body using LB foot, FA flange, SDB pivot or TC trunnion brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X135CA FAQ
This double-acting cylinder has a 25 mm bore and 135 mm stroke. It pushes 245.3 N and pulls 206.1 N at 0.5 MPa, and pushes 343.4 N / pulls 288.5 N at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa. It uses a 1/8 inch air port and an M10x1.25 male rod thread.
No, this specific SKU does not include a magnet. You must order the -S version to use CMSG, DMSG or EMSG switches. The defining feature here is the adjustable air cushion at both ends, which only decelerates the load near stroke end and does not lock or hold the position pneumatically.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X135CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.