Airtac MIC Cushioned Mini Cylinder MIC25X90SCA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X90SCA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 90mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X90SCA
Dial in end-of-stroke deceleration with the AirTAC MIC25X90SCA, a double-acting round-body mini cylinder built for high-speed actuation. Its stainless-steel barrel and Ø10 piston rod shrug off mild corrosion and washdown environments. A needle-set variable air cushion at both ends absorbs kinetic energy to protect your payload, a distinct upgrade over fixed rubber bumpers. Driven by a 1/8" port, this ISO 6432 mounting-interface unit pushes with 245.3 N and pulls with 206.1 N at 0.5 MPa.
For sizing context, this bore yields a safe working load of roughly 147 N, meaning it lifts about 12.5 kg vertically with a 2:1 safety margin. The rear CA pivot cover simplifies clevis mounting. Because the -S suffix denotes a built-in piston magnet, you can directly mount CMSG, DMSG, or EMSG position switches for reed or electronic sensing.
Airtac MIC Cushioned Mini Cylinder MIC25X90SCA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X90SCA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 90 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X90SCA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X90SCA Is Used
Package Diverters
Handles 12.5 kg cartons at high cycle rates on sorting lines, using the adjustable cushion to prevent jarring stops that misalign boxes.
Filler Head Actuation
Drives vertical filler nozzles smoothly into containers, relying on the stainless construction for wipe-down compatibility in food or chemical zones.
Component Seating
Presses lightweight bearings or pins into housings, using the 245.3 N thrust at 0.5 MPa to seat parts without marring surfaces.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X90SCA the Right Cylinder?
If you need less force, the smaller Ø20 bore provides 157 N of push at 0.5 MPa, whereas stepping up to the Ø32 bore yields 402 N. Choose this Ø25 model when moving loads at high speeds where the adjustable air cushion prevents harsh end-of-stroke impacts. Remember that the cushion only decelerates the piston near stroke end; it is not a brake. If your application must hold a load vertically during air loss, install an external rod lock or pilot-operated check valve. You can pair this unit with LB foot, FA flange, or TC trunnion hardware to suit your frame.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X90SCA FAQ
At 0.5 MPa it pushes with 245.3 N and pulls with 206.1 N. At 0.7 MPa the push is 343.4 N and pull is 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa. This bore uses a 1/8" air port and features a Ø10 mm piston rod with an M10x1.25 male thread.
The cylinder uses a needle-set variable air cushion at both ends to decelerate the piston smoothly at high speeds, reducing shock and noise. It is not a locking brake. Because this SKU includes the -S magnet, you can attach CMSG, DMSG, or EMSG switches for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X90SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.