Airtac ACED Double-acting Compact Cylinder ACED50X175
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED50X175 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø50mm bore and 175mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ50 mm
- Stroke175 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED50X175
A double acting compact cylinder built to ISO 21287, the ACED50X175 pushes a 16 mm rod out of BOTH covers, so its 50 mm bore delivers the same 881.2 N at 0.5 MPa (1233.7 N at 0.7 MPa) on every stroke. The through-rod resists rotation and side load and gives a symmetric mount, while the back-end rod can carry a sensor flag on pick-and-place gantries.
The hard-anodized aluminium body with an S45C hard-chrome plated rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, with a fixed TPU bumper at each end. Its short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight guarding where a full-length body will not fit. In practice the 881.2 N at 0.5 MPa means you can plan on roughly 529 N of real work, and with a 2:1 margin it lifts about 45 kg vertically.
Airtac ACED Double-acting Compact Cylinder ACED50X175 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED50X175 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED50X175
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 50 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED50X175 Is Used
Reciprocating transfer arm
The through-rod gives a mounting point on both covers, so a slide carriage can be driven from either end at 881.2 N while the rod resists rotation over the 175 mm travel.
Clamp fixture with rear sensor flag
Mount the fixture on the front rod and a CMSE / DMSE switch flag on the rear rod (with the optional -S magnet) to confirm clamped position inside a compact welding jig.
Vertical press station
With about 45 kg of vertical lift capacity at a 2:1 margin, the 50 mm bore handles ejection or stamping of aluminium housings at up to 500 mm/s.
Is the Airtac ACED Double-acting Compact Cylinder ACED50X175 the Right Cylinder?
At 881.2 N per side at 0.5 MPa, the 50 mm bore sits between the 40 mm bore (571.8 N) and the 63 mm bore (1458.1 N), so step up to 63 mm if your jig needs more margin at the same pressure. The 175 mm stroke is within the 250 mm standard range for this bore, so no made-to-order build is required. Remember that a plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check for held loads. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the ISO 21287 face, and order the -S code if you want the optional magnet for CMSE / DMSE switches - without -S there is no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED50X175 FAQ
Yes - a rod exits both covers, so both strokes use the rod-side area. Output is 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa in EITHER direction, with a maximum of 179.7 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port depends only on the 50 mm bore.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium body, S45C hard-chrome rod and a fixed TPU bumper at each end. Sensing is not fitted as standard: order the -S code to get the optional magnet, which lets CMSE / DMSE switches read position along the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED50X175
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.