AirTAC HFTKL Long-Stroke Parallel Gripper, Ø10 to Ø25
Every stocked AirTAC HFTKL gripper on one page: 16 order codes in 4 bore sizes from Ø10 to Ø25 mm, from $162.81. Pick the bore and jaw type to see the exact order code and price.
Standard jaw
This combination is not a stock order code. Request a quote and we will confirm availability and price.
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC HFTKL
The AirTAC HFTKL is a long-stroke parallel pneumatic gripper whose two jaws run on an integrated crossed-roller linear guide, giving high rigidity, precision and load capacity. It is single acting, normally open: with no air the spring keeps the jaws open, and air closes them. The catalog rates its air-driven closing force. Jaw stroke is 8 to 22 mm (both sides) across Ø10 to Ø25 mm bores. That is a longer stroke than the HFK at the same bore, for example 12 mm against 6 mm on Ø16.
Locating pins under the guide keep it aligned with the body, and a locating hole in the body makes repeat mounting accurate. The body mounts from the side, the front (tapped or through holes) or the rear. Every version has a magnet, with round and square sensor grooves on the body so sensors fit without brackets.
HFTKL Technical Specifications
| Model | HFTKL |
|---|---|
| Action | Single acting, normally open |
| Guide | Integrated crossed-roller linear guide |
| Ø10 | closing 7 N · stroke 8 mm · 73 g (74 g with F jaw) |
| Ø16 | closing 27 N · stroke 12 mm · 155 g (154 g with F jaw) |
| Ø20 | closing 35 N · stroke 18 mm · 292 g (294 g with F jaw) |
| Ø25 | closing 55 N · stroke 22 mm · 525 g (530 g with F jaw) |
| Fluid | Air (filtered by 40 µm element) |
|---|---|
| Operating pressure | 0.35-0.7 MPa on Ø10, 0.25-0.7 MPa on Ø16 and up |
| Temperature | -20 to +70 °C |
| Lubrication | Not required |
| Repeatability | ±0.01 mm |
| Max frequency | 120 c.p.m. |
| Port | M3×0.5 (Ø10), M5×0.8 (Ø16 and up) |
| Sensors | CMSH/DMSH/EMSH; CMSG/DMSG/EMSG on Ø16 and up |
Source: AirTAC Products Catalog 2026A (PDF01-P0644..P0645), HFKL series specifications and ordering code. Forces are per jaw at 0.5 MPa, gripping distance L = 20 mm.
How the HFTKL Order Code Is Built
| HFTKL | Long-Stroke Parallel gripper, single acting, normally open |
|---|---|
| 10 / 16 / 20 / 25 | Bore (mm) |
| blank / B / N / F | Jaw: standard, side mounting, through-hole mounting, bottom mounting |
All AirTAC HFTKL Order Codes (16)
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Bore | Mounting | Width | Price | Select |
|---|---|---|---|---|---|
| HFTKL10 | Ø10 mm | Standard | Standard jaw | $162.81 | |
| HFTKL10B | Ø10 mm | Side mounting | Standard jaw | $162.81 | |
| HFTKL10N | Ø10 mm | Through-hole mounting | Standard jaw | $162.81 | |
| HFTKL10F | Ø10 mm | Bottom mounting | Standard jaw | $162.81 | |
| HFTKL16 | Ø16 mm | Standard | Standard jaw | $172.12 | |
| HFTKL16B | Ø16 mm | Side mounting | Standard jaw | $172.12 | |
| HFTKL16N | Ø16 mm | Through-hole mounting | Standard jaw | $172.12 | |
| HFTKL16F | Ø16 mm | Bottom mounting | Standard jaw | $172.12 | |
| HFTKL20 | Ø20 mm | Standard | Standard jaw | $188.40 | |
| HFTKL20B | Ø20 mm | Side mounting | Standard jaw | $188.40 | |
| HFTKL20N | Ø20 mm | Through-hole mounting | Standard jaw | $188.40 | |
| HFTKL20F | Ø20 mm | Bottom mounting | Standard jaw | $188.40 | |
| HFTKL25 | Ø25 mm | Standard | Standard jaw | $225.62 | |
| HFTKL25B | Ø25 mm | Side mounting | Standard jaw | $225.62 | |
| HFTKL25N | Ø25 mm | Through-hole mounting | Standard jaw | $225.62 | |
| HFTKL25F | Ø25 mm | Bottom mounting | Standard jaw | $225.62 |
Need a combination that is not listed? Request a quote.
Where the HFTKL Is Used
Pick and place
Picks parts on assembly and transfer lines.
Machine loading
Loads and unloads workpieces on presses and machine tools.
Opens on air loss
The spring keeps the jaws open if the air supply drops.
Choosing the Right HFTKL Configuration
Choose the bore by the closing force you need at 0.5 MPa (see the specifications; forces are for one jaw at gripping distance L = 20 mm as defined in the catalog). A longer gripping distance lowers the usable force.
Then the jaw type, which sets how your fingers attach: standard (no code), B side mounting, N through-hole mounting, F bottom mounting.
For other actions see the HFKL and HFSKL pages.
AirTAC HFTKL FAQ
The HFTKL is single acting, normally open; the HFKL is double acting; the HFSKL is single acting, normally closed. Otherwise they share the same bores and jaw types.
Blank is the standard jaw, B side mounting, N through-hole mounting, F bottom mounting. The long-stroke series has no wide-jaw versions.
Every version has a built-in magnet. Sensors are ordered separately: CMSH, DMSH or EMSH for the round groove on all bores, and CMSG, DMSG or EMSG for the square groove on Ø16 and up.
0.35-0.7 MPa on Ø10, 0.25-0.7 MPa on Ø16 and up, -20 to +70 °C, on air filtered to 40 µm. No lubrication is needed.
No. You can order a single piece. Orders are processed and handed to the carrier within 3-5 business days.
Buying the HFTKL from AirtacDistr
Genuine AirTAC parts
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
Ready in 3-5 business days
That is our time to process the order and hand it to the carrier. No minimum order: a single piece can be ordered.
14-day returns, 1-year warranty
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Engineering help
Send your application details and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-11-03.
Request a Quote for the HFTKL
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.