Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S
The AirTAC Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S is a genuine double acting, adjustable stroke ISO 21287 compact air cylinder with a Ø100mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S
A double acting AirTAC ACEJ100X10-10S delivers 3927 N push and 3769.9 N pull at 0.5 MPa, rising to 5497.8 N at 0.7 MPa, with a theoretical peak of 800.9 kgf at 1.0 MPa. The -10 code gives a 10 mm adjustment window: an external stop screw trims the 10 mm extend stroke on site, so the usable extend range is 0-10 mm. The body is a hard-anodized ISO 21287 compact build whose short frame saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into press fixtures and guarding where a full-length body cannot go.
This 100 mm bore moves serious mass: plan on roughly 2356 N (about 240 kg) of real working push at 0.5 MPa, which corresponds to lifting about 200 kg vertically with a 2:1 margin. The S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clamped into the body slots for end-of-stroke signalling. A fixed TPU bumper at each end absorbs end-of-stroke energy, the S45C hard-chrome rod resists wear, and speed spans 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S Technical Specifications
| Model | Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 10 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3770 N |
| 0.7 MPa | 5498 N | 5278 N |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 100 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S Is Used
Short-stroke press marking
Stamping batch codes or logos on aluminium castings needs only a few millimetres of travel; the 0-10 mm trimmed stroke and 3927 N push at 0.5 MPa give a crisp, repeatable mark.
Pallet clamp actuation
Clamping heavy pallets or fixtures in machining cells: the 100 mm bore holds with about 240 kg of usable working force, and the compact body fits inside the clamp arm.
Gated ejection with position check
Kicking rejected parts off a conveyor end: the fitted magnet drives CMSE or DMSE switches so the PLC confirms each 10 mm eject completed before the next cycle.
Is the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S the Right Cylinder?
At 100 mm bore this is the second-largest ACEJ size: it out-pushes the 80 mm bore (2513 N at 0.5 MPa) and sits one step below the 125 mm bore (6135.9 N at 0.5 MPa). If your load needs under about 240 kg of working force, the 80 mm saves space; if you are near the limit, step up. The 10 mm stroke with a 10 mm window suits short clinching, marking or ejection moves. Remember the stop screw is a mechanical end stop for the extend stroke only - on air loss the piston still drifts, so add a separate holding valve where a load must stay put. FA flange or LB foot mountings bolt to the ISO 21287 face, and the fitted -S magnet accepts CMSE / DMSE switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S FAQ
At 0.5 MPa it pushes 3927 N and pulls 3769.9 N; at 0.7 MPa push is 5497.8 N and pull 5277.9 N, with a theoretical maximum of 800.9 kgf at 1.0 MPa. The -10 code sets a 10 mm adjustment window: turn the external stop screw to shorten the 10 mm extend stroke anywhere in that range, giving 0-10 mm of usable travel. The stop is a mechanical end stop, not a mid-stroke lock - on air loss the piston still drifts. Speed range is 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
The hard-anodized aluminium ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight guards and fixtures. This model carries the optional -S magnet, so CMSE reed or DMSE solid-state switches mount directly in the body slots. A fixed TPU bumper at each end absorbs end-of-stroke energy, the rod is S45C steel with hard chrome and a female M12x1.75 thread, the port is 1/8" PT, and FA flange or LB foot mountings bolt straight on.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ100X10-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.