Airtac ATQ Single Acting Thin Cylinder ATQ20X10B
The AirTAC Airtac ATQ Single Acting Thin Cylinder ATQ20X10B is a genuine single-acting COMPACT (JIS) cylinder (single acting, pull type) with a Ø20mm bore and 10mm stroke. Air pulles the rod and an internal spring performs the opposite stroke, so one solenoid line drives the motion — ideal for short-stroke clamping and ejection in tight spaces.
- BoreØ20 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeSingle acting, pull type
- Rod threadM5×0.8 (F) / M8×1.25 (B)
- CushionBumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ATQ Single Acting Thin Cylinder ATQ20X10B
The AirTAC ATQ20X10B is a single-acting PULL-type compact cylinder where compressed air fed to one M5x0.8 port retracts the 10mm piston rod, while an internal spring extends it upon exhaust. It delivers 117.8N of theoretical pull at 0.5 MPa and 164.9N at 0.7 MPa. Because an internal return spring counteracts the air pressure, the actual net output force is lower and should be verified from the datasheet for your specific load.
Designed for short-stroke tasks, this 10mm travel unit stays within the 30mm maximum limit for its 20mm bore. The body incorporates fixed TPU elastomer bumpers at each end to soften end-of-stroke impacts, replacing complex adjustable cushions. It requires a minimum 0.2 MPa operating pressure to overcome the spring, and the male M8x1.25 rod end threads directly onto your mechanism.
Airtac ATQ Single Acting Thin Cylinder ATQ20X10B Technical Specifications
| Model | Airtac ATQ Single Acting Thin Cylinder ATQ20X10B |
|---|---|
| Series | ATQ JIS compact single-acting cylinder |
| Bore size | Ø20 mm |
| Stroke | 10 mm |
| Acting type | Single acting, pull type |
| Port size | M5×0.8 |
| Rod end thread | M5×0.8 female / M8×1.25 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Bumper |
| Max standard stroke | Up to 30 mm |
Specifications follow the official AirTAC ACQ-family datasheet. Single-acting types start at 0.2 MPa (the spring must be overcome). Confirm against the product label before installation.
Theoretical Output Force (Ø20mm, Pull)
| Pressure | Pull force (before spring) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
These are theoretical air-side forces; the return-spring force reduces the NET usable output. Single-acting pull only — the spring performs the opposite stroke. Confirm the net figure from the datasheet and size with a safety margin.
Model Code: Airtac ATQ Single Acting Thin Cylinder ATQ20X10B
| ATQ | JIS compact single acting, pull type cylinder series. |
|---|---|
| 20 | Bore size in mm. |
| ×10 | Stroke length in mm (single-acting max 30 mm). |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| B | Male-thread piston rod (omit = female thread). |
Thread: PT standard (G / NPT available). ASQ pushes out / spring returns; ATQ pulls in / spring extends. Related: ACQ (double acting), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac ATQ Single Acting Thin Cylinder ATQ20X10B Is Used
Clamp Release Mechanism
Uses the spring-extend fail-safe to hold a workpiece securely, then applies air to pull the clamp open when the machining cycle finishes.
Package Stopper Gate
Retracts a physical stop gate out of the conveyor path to let cartons pass, relying on the internal spring to redeploy the barrier.
Tensioning Arm
Draws back a tensioning idler arm against a belt drive, providing consistent mechanical pull that releases instantly upon air exhaustion.
Is the Airtac ATQ Single Acting Thin Cylinder ATQ20X10B the Right Cylinder?
For sizing, stepping down to the 16mm bore yields 75.4N of theoretical pull at 0.5 MPa, while moving up to the 25mm bore provides 188.9N at that same pressure. If your mechanism needs more than the 30mm maximum travel allowed for this 20mm bore, you must switch to the double-acting ACQ series. When ordering this ATQ variant, confirm the 10mm stroke, the lack of a magnet, and the male M8x1.25 rod thread.
Quick checklist
- ✓ Net pull force (after spring) at your pressure
- ✓ Stroke ≤ 30 mm (single-acting limit)
- ✓ Single air line saves a valve/port
- ✓ Magnet (S) for sensors?
- ✓ Female (blank) or male (B) rod thread
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.2 – 1.0 MPa operating pressure.
- check Remember the spring performs the return stroke.
- check Avoid side load on the short piston rod.
- check Handle the C-clip carefully; seat it fully in its groove.
- check Installation by qualified personnel per AirTAC docs.
Airtac ATQ Single Acting Thin Cylinder ATQ20X10B FAQ
It provides a theoretical pull of 117.8N at 0.5 MPa and 164.9N at 0.7 MPa, though the internal spring lowers the net output. It requires a minimum of 0.2 MPa to function, and the 20mm bore limits the maximum standard stroke to 30mm.
Fixed TPU elastomer bumpers absorb impact energy at the stroke ends without any adjustable air cushioning. In a loss of air pressure, the fail-safe internal spring automatically extends the rod to its resting outward position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC ATQ Cylinders
Request a Quote for Airtac ATQ Single Acting Thin Cylinder ATQ20X10B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.