Airtac JSID Double Rod Cylinder JSID32X200
The AirTAC Airtac JSID Double Rod Cylinder JSID32X200 is a genuine double acting, double rod JIS-standard air cylinder with a Ø32mm bore and 200mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke200 mm
- Port sizeG1/8
- Acting typeDouble acting, double rod
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID32X200
Delivering 345 N of thrust in both directions at 0.5 MPa, the AirTAC JSID32X200 uses a twin-rod layout to equalize output force. Because the piston rod passes through both end covers, the active pressure area is identical on the extend and retract strokes. This makes the unit ideal for symmetric load paths and anti-rotation guidance. It yields a safe working load of about 207 N, which translates to lifting roughly 18 kg vertically with a 2:1 safety margin.
Built to JIS standards, this hard-anodized aluminum profile barrel is noticeably shorter than an ISO 15552 cylinder of the same 32 mm bore. It features a G1/8 port, an M10x1.25 rod thread, and adjustable air cushions at both ends. Note that this specific SKU lacks a magnet and cannot accept position sensors; adding the -S variant enables CMSE or DMSE switches. The cushion only decelerates the load near stroke end, so fit an external rod lock or pilot-operated check valve if you need to hold a load on air loss.
Airtac JSID Double Rod Cylinder JSID32X200 Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID32X200 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) | — |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID32X200
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID32X200 Is Used
Dual-End Tooling Shuttle
Drives two identical pick-and-place grippers from opposite rod ends to alternately load and unload parts in a synchronous indexing dial table.
Symmetric Lift Platform
Balances a 18 kg vertical payload evenly through the center to prevent chassis twisting during upward and downward transfer strokes.
Anti-Rotation Clamp
Holds a workpiece flat against a machining fixture using the inherent torsional resistance of the dual-rod piston to prevent angular drift.
Is the Airtac JSID Double Rod Cylinder JSID32X200 the Right Cylinder?
If 345 N each way is too much force, step down is not an option as 32 mm is the smallest bore in the JSID range. If you need more power, the 40 mm bore provides 528 N at 0.5 MPa. Choose this double-rod configuration when you need to drive two tools simultaneously, prevent twist on a vertical lift, or mount a sensor cam on the back end. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2. For the 200 mm stroke, ensure external guide rails are used to absorb any lateral side loads and prevent binding. Remember that this non-magnet version cannot host switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID32X200 FAQ
The force is equal in both directions because of the double-rod design. It outputs 345 N at 0.5 MPa and 483 N at 0.7 MPa. The theoretical maximum force is 70 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa.
No, this specific SKU does not have a magnet and cannot accept a sensor. You must order the -S variant of the JSID32X200 to use CMSE or DMSE magnetic switches for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID32X200
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.