Airtac JSID Double Rod Cylinder JSID32X225
The AirTAC Airtac JSID Double Rod Cylinder JSID32X225 is a genuine double acting, double rod JIS-standard air cylinder with a Ø32mm bore and 225mm stroke, G1/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ32 mm
- Stroke225 mm
- Port sizeG1/8
- Acting typeDouble acting, double rod
- Rod threadM10×1.25
- CushionAdjustable, 20 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID32X225
Delivering 345 N of equal force in both directions at 0.5 MPa, this 32 mm bore double-rod cylinder uses a single piston with a rod exiting each cover. The symmetric layout creates a balanced load path that resists torsion, making it ideal for non-rotating guidance or driving twin tooling simultaneously. Built to JIS standards with an extruded hard-anodized aluminum profile barrel, the unit is notably shorter than an ISO 15552 cylinder of the same bore.
Air enters through a G1/8 port to drive the 12 mm rod at speeds of 30-800 mm/s. Based on the 0.5 MPa output, this actuator handles a safe working load of about 207 N, which translates to lifting roughly 18 kg vertically with a 2:1 margin. This specific SKU lacks a magnet, so it cannot accept CMSE or DMSE sensors; choose the -S variant for position detection.
Airtac JSID Double Rod Cylinder JSID32X225 Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID32X225 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20 mm |
| Max standard stroke | Up to 1000 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) | — |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID32X225
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 32 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID32X225 Is Used
Twin-Tool Transfer
Drives two opposing pickers simultaneously from one piston, keeping cycle times synchronized without adding a second actuator.
Anti-Rotation Lift
The dual-rod geometry prevents twist during vertical elevation, securely moving light jigs without requiring external linear rails.
Symmetric Clamping
Applies equal clamping pressure from both ends of a workpiece at once, ensuring balanced holding force for light machining.
Is the Airtac JSID Double Rod Cylinder JSID32X225 the Right Cylinder?
For sizing context, stepping up to the 40 mm bore yields 528 N each way, while the 32 mm sits at the low edge of the range with its 345 N equal-both-ways output. Choose this double-rod layout when your mechanism demands anti-rotation stability, symmetric load distribution, or a rear rod end to mount a sensor cam. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2. Because the stroke is 225 mm, which is under the 300 mm side-load threshold, standard guiding is usually sufficient, though external guides always extend seal life. Note that without live air, a plain cylinder drifts; the adjustable cushions only decelerate the stroke, so fit an external rod lock or pilot-operated check valve if you need to hold a load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID32X225 FAQ
The G1/8 port feeds a 32 mm bore that outputs 345 N at 0.5 MPa and 483 N at 0.7 MPa. Because it is a double-rod design, this force is exactly equal in both directions. The theoretical maximum is 70 kgf at 1.0 MPa.
No, this specific SKU does not have a magnet and cannot accept CMSE or DMSE switches. You must select the -S variant to enable position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID32X225
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.