Airtac JSID Double Rod Cylinder JSID63X10
The AirTAC Airtac JSID Double Rod Cylinder JSID63X10 is a genuine double acting, double rod JIS-standard air cylinder with a Ø63mm bore and 10mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ63 mm
- Stroke10 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod
- Rod threadM18×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID63X10
Delivering 1402 N of equal force in both directions at 0.5 MPa, this 63 mm bore double-rod actuator uses a G3/8 port and a 10 mm stroke. Because the piston rod passes through both covers, the effective area is identical on the extend and retract strokes, completely eliminating the force differential found in single-rod designs. This symmetric layout provides inherent anti-rotation guidance and allows you to mount tooling or a sensor cam on the back end simultaneously.
Built to JIS standards with an extruded hard-anodized aluminum profile barrel, the body is noticeably shorter and more compact than an ISO 15552 cylinder of the same bore. The 1402 N output translates to a safe working load of about 841 N, which is enough to vertically lift roughly 71 kg with a 2:1 safety margin. Note that this specific SKU lacks a magnet and cannot accept CMSE/DMSE sensors; choose the -S variant if switch tracking is required.
Airtac JSID Double Rod Cylinder JSID63X10 Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID63X10 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) | — |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 318 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID63X10
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID63X10 Is Used
Twin-Spindle Lifting
Drives two synchronized lifting stages from opposite rod ends, ensuring parallel vertical movement without mechanical binding.
Symmetric Transfer Gate
Powers a diverter gate where the equal push and pull force prevents twisting under asymmetric package loads.
Dual-Action Press Tooling
Mounts a forming tool on the front rod and a return cam on the rear, keeping the load path perfectly centered.
Is the Airtac JSID Double Rod Cylinder JSID63X10 the Right Cylinder?
When sizing this 63 mm bore, stepping down to a 50 mm unit drops the equal-both-ways force to 825 N at 0.5 MPa, while stepping up to an 80 mm bore increases it to 2268 N. A double-rod configuration is the right call when your application demands strict anti-rotation stability, symmetric load distribution, or twin tooling driven from both ends. Mounting options include FA, LB, TC, TCM1, and TCM2 brackets. Because this is a non-magnetized model, position sensing is not possible without upgrading to the -S version. For any stroke at or above 300 mm, always use an external guide to prevent side-load damage to the seals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID63X10 FAQ
The force is equal in both directions because of the double-rod design. It provides 1402 N at 0.5 MPa and 1962 N at 0.7 MPa. The theoretical maximum is 286 kgf at 1.0 MPa using the pull-side area.
No, a plain double-rod cylinder will drift if air pressure drops or the valve is centered. The adjustable 29 mm air cushions only decelerate the piston near the stroke ends and do not act as a brake. To maintain a vertical load, you must add an external rod lock or a pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID63X10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.