Airtac JSID Double Rod Cylinder JSID80X800
The AirTAC Airtac JSID Double Rod Cylinder JSID80X800 is a genuine double acting, double rod JIS-standard air cylinder with a Ø80mm bore and 800mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ80 mm
- Stroke800 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod
- Rod threadM22×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID80X800
Delivering 2268 N of thrust in both directions at 0.5 MPa, this 80 mm bore double-rod actuator uses a single piston with a rod exiting each cover. The symmetric layout prevents rotation and provides a stable load path for demanding jobs. With a safe working load around 1361 N, it can vertically lift roughly 116 kg with a 2:1 margin. Built to JIS standards, its extruded hard-anodized aluminium profile barrel is noticeably shorter than a same-bore ISO 15552 unit.
This specific SKU lacks a magnet, so it cannot accept CMSE or DMSE sensors without switching to an -S variant. It features a G3/8 port, an M22x1.5 rod thread, and adjustable 29 mm air cushions at both ends. The 800 mm stroke is well within the 1500 mm standard limit, though an external guide is strongly recommended to prevent rod bending over this long travel. Note that the cushions only decelerate the load; use an external rod lock or pilot-operated check valve to hold position.
Airtac JSID Double Rod Cylinder JSID80X800 Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID80X800 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 800 mm |
| Acting type | Double acting, double rod |
| Port size | G3/8 |
| Rod thread | M22×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) | — |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | 3175 N |
| Max (@1.0 MPa) | 513 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID80X800
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 80 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID80X800 Is Used
Dual-Station Transfer
Uses both rod ends to push and pull parts simultaneously across a conveyor, leveraging the equal 2268 N force for balanced dual-station cycling.
Symmetric Lift Press
Applies the anti-twist advantage of the double rod to press or lift heavy assemblies straight down, maintaining parallelism without external guides.
Long-Stroke Ejector
Employs the full 800 mm travel to eject large fabricated parts from a machine bed, relying on adjustable cushions to decelerate the mass at stroke end.
Is the Airtac JSID Double Rod Cylinder JSID80X800 the Right Cylinder?
When sizing this double-rod actuator, stepping down to a 63 mm bore yields 1402 N each way, while moving up to a 100 mm bore provides 3574 N. Choose the 80 mm bore when your application demands approximately 2268 N of equal bidirectional force. A twin-rod design is the right call when you need anti-rotation guidance, symmetric load distribution, or a rear rod end to drive a second tool. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2. Because this is a non-magnet SKU, position sensing is unavailable. For the 800 mm stroke, always support the load with an external linear guide to avoid excessive side-load and rod bending.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID80X800 FAQ
Because the rod passes through both covers, force is equal in both directions: 2268 N at 0.5 MPa and 3175 N at 0.7 MPa, with a theoretical max of 463 kgf at 1.0 MPa. The air port size is G3/8, and the rod-end thread is M22x1.5.
No, this plain SKU lacks a magnet and cannot take CMSE or DMSE sensors. Additionally, the air cushions only decelerate the piston near stroke end; they do not hold load. For vertical holding, you must install an external rod lock or a pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID80X800
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.