Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40
The AirTAC Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 is a genuine double-acting aluminum-barrel mini cylinder with a Ø32mm bore, a 60mm nominal stroke and a rear adjustable-stroke stopper — trim up to 40mm for a usable window of 20–60mm. Adjustable air cushion (both ends).
- BoreØ32 mm
- Stroke60 mm
- Adjustable20–60 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable air cushion (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40
The AirTAC MBLCJ32X60-40 is a compact double-acting mini cylinder featuring a riveted aluminum barrel and a Ø12 mm hard-chrome plated carbon-steel rod. It integrates a rear travel stopper allowing you to trim up to 40 mm, yielding a usable stroke window of 20 to 60 mm. Simultaneously, twin screw-tunable air cushions decelerate the piston near each end-cap, absorbing kinetic energy to prevent end-cover damage during rapid 563 N push strokes at 0.7 MPa.
Because this specific SKU lacks the -S magnet suffix, it cannot host CMSG, DMSG, or EMSG position switches. The heterogeneous two-way grease-retaining piston seal maintains lubrication across the 30-800 mm/s speed range, while the G1/8 port feeds the 402 N extension force. Remember the rear adjuster sets a physical end position but holds no load; the cushion only slows transit speed.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 Technical Specifications
| Model | Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder (adjustable stroke) |
| Bore size | Ø32 mm |
| Nominal stroke | 60 mm |
| Adjustable window | 20–60 mm (trim 40 mm) |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable air cushion (both ends) |
| Max standard stroke | Up to 500 mm |
The rear stopper sets the end position — it is a travel stop, not a lock. Overall length = A + 2 × stroke + adjustable stroke. MBLJ/MBLCJ mounting is Basic / FA / LB only (no SDB, no back-cover code). Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a margin.
Model Code: Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40
| MBLCJ | MBLCJ aluminum-barrel adjustable-stroke mini cylinder with adjustable cushion. |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Nominal stroke length in mm. |
| -40 | Adjustable-stroke amount (mm you can trim at the rear). |
| S | Optional built-in magnet for a CMSG/DMSG/EMSG sensor switch. |
Related: MBLJ (adjustable stroke, fixed bumper), MBL (fixed stroke), MBLD (double rod).
Where the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 Is Used
PCB Router Z-Axis
Governs the 20-60 mm plunge of a spindle carriage, using the tunable cushion to soften the 346 N retraction stop and protect fine-pitch router bearings.
Dispenser Valve Tensioning
Trims the exact closure position of a fluid dispense head, relying on the 402 N push force to consistently seat the nozzle against a cartridge.
Textile Loom Takedown
Actuates the fabric take-up claw in a narrow weaving frame, where the compact 32 mm body fits between guide rails and the rear stopper sets beat length.
Is the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 the Right Cylinder?
If you need less thrust, stepping down to the 25 mm bore yields 245 N push at 0.5 MPa, whereas moving up to the 40 mm bore provides 628 N. Choose this MBLCJ over the MBLJ when your moving mass requires tunable end-deceleration rather than a fixed rubber bumper, or over the MBLC when you need to fine-tune the travel endpoint within that 20-60 mm window. Neither the cushion needle nor the stroke adjuster acts as a mechanical lock—external flow controls or guide rails are required to hold a load. Mounting is restricted to Basic, FA flange, or LB foot styles (no SDB pivot or back-cover), and the PT thread port must be matched exactly when replacing this unit.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Adjustable window fits your end position
- ✓ Adjuster is a travel stop, not a lock
- ✓ Magnet (S) for sensors?
- ✓ Side load — add a guide on long strokes
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear stopper for the end position (a travel stop, not a lock).
- check Avoid side load; add an external guide on long strokes.
- check Mounting: Basic / FA flange / LB foot (no SDB, no back-cover code).
- check Installation by qualified personnel per AirTAC docs.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40 FAQ
At 0.5 MPa it provides 402 N push and 346 N pull. At 0.7 MPa the extension force is 563 N, and the maximum theoretical output is 82 kgf at 1.0 MPa.
No, because this SKU lacks the -S suffix, it has no built-in magnet and cannot accept CMSG, DMSG, or EMSG switches. You must select an MBLCJ model with the S code for solid-state or reed sensor detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Adjustable-Stroke Cylinders
Request a Quote for Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.