Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50
The AirTAC Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 is a genuine double-acting aluminum-barrel mini cylinder with a Ø32mm bore, a 60mm nominal stroke and a rear adjustable-stroke stopper — trim up to 50mm for a usable window of 10–60mm. Adjustable air cushion (both ends).
- BoreØ32 mm
- Stroke60 mm
- Adjustable10–60 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable air cushion (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50
The AirTAC MBLCJ32X60-50 is a compact double-acting mini round cylinder featuring a single Ø12mm carbon-steel rod and a riveted aluminum barrel. It combines a rear travel stopper with an adjustable air cushion at both ends. The rear adjuster allows you to trim up to 50mm of travel, creating a usable stroke window of 10-60mm for precise end-position tuning. Delivering 402N of push force at 0.5MPa, this 60mm stroke unit is built for dynamic positioning tasks.
Unlike the base MBLJ which relies on a fixed rubber bumper, this model uses screw-tunable end-of-stroke deceleration to protect the end covers during faster or heavier moves. The rear stopper sets the travel end but does not hold the load, and the cushion only decelerates; neither acts as a lock. Because this specific SKU lacks the -S magnet code, it cannot accept an AirTAC CMSG, DMSG, or EMSG position sensor. The two-way grease-retaining piston seal maintains lubrication over a 30-800mm/s speed range.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 Technical Specifications
| Model | Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder (adjustable stroke) |
| Bore size | Ø32 mm |
| Nominal stroke | 60 mm |
| Adjustable window | 10–60 mm (trim 50 mm) |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable air cushion (both ends) |
| Max standard stroke | Up to 500 mm |
The rear stopper sets the end position — it is a travel stop, not a lock. Overall length = A + 2 × stroke + adjustable stroke. MBLJ/MBLCJ mounting is Basic / FA / LB only (no SDB, no back-cover code). Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a margin.
Model Code: Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50
| MBLCJ | MBLCJ aluminum-barrel adjustable-stroke mini cylinder with adjustable cushion. |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Nominal stroke length in mm. |
| -50 | Adjustable-stroke amount (mm you can trim at the rear). |
| S | Optional built-in magnet for a CMSG/DMSG/EMSG sensor switch. |
Related: MBLJ (adjustable stroke, fixed bumper), MBL (fixed stroke), MBLD (double rod).
Where the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 Is Used
PCB Drill Head Indexing
Drives a 402N push to cycle a drilling head carriage into position, using the 10-60mm stroke window to fine-tune the exact drilling depth without moving mechanical hard stops.
Bottle Capper Alignment
Applies 346N of retraction force to lower a capping head, relying on the screw-tunable air cushion to prevent cap crushing when sealing beverage containers at high speed.
Textile Fabric Guide
Shifts a fabric edge guide roller by up to 50mm, using the rear travel stopper to set the exact correction limit while the riveted aluminum body fits into tight loom spacing.
Is the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 the Right Cylinder?
When sizing this 32mm bore (402N push at 0.5MPa), consider stepping down to the 25mm bore (245N push) for lighter duties, or up to the 40mm bore (628N push) if your load requires more force. Choose the MBLCJ over the MBLJ when your application demands tunable end-deceleration rather than a fixed bumper, or the MBLC if you need a fixed stroke without the rear travel adjuster. The adjuster and cushion are not brakes; use an external locking device if you must hold position without live air. Mounting is limited to Basic, FA flange, or LB foot (no SDB or back-cover options). For a direct replacement, match the 32mm bore, 60mm stroke, 50mm adjust code, G1/8 port, default PT thread, and no-magnet configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Adjustable window fits your end position
- ✓ Adjuster is a travel stop, not a lock
- ✓ Magnet (S) for sensors?
- ✓ Side load — add a guide on long strokes
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear stopper for the end position (a travel stop, not a lock).
- check Avoid side load; add an external guide on long strokes.
- check Mounting: Basic / FA flange / LB foot (no SDB, no back-cover code).
- check Installation by qualified personnel per AirTAC docs.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50 FAQ
At 0.5MPa, the push force is 402N and the pull force is 346N. At 0.7MPa, the push force increases to 563N. The maximum theoretical force is 82kgf at 1.0MPa, with an operating pressure range of 0.15-1.0MPa.
The adjustable stroke is a rear travel stopper that lets you trim up to 50mm of movement, creating a 10-60mm usable window. The adjustable air cushion is a screw-tunable valve that controls deceleration at the stroke ends. Neither holds the load; the adjuster is a stop and the cushion only decelerates.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Adjustable-Stroke Cylinders
Request a Quote for Airtac MBLCJ Adjustable Mini Cylinder MBLCJ32X60-50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.