Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S
The AirTAC Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S is a genuine double-acting aluminum-barrel mini cylinder with a Ø63mm bore, a 15mm nominal stroke and a rear adjustable-stroke stopper — trim up to 10mm for a usable window of 5–15mm. Adjustable air cushion (both ends).
- BoreØ63 mm
- Stroke15 mm
- Adjustable5–15 mm
- Port sizeG1/4
- Acting typeDouble acting
- Rod threadM14×1.5
- CushionAdjustable air cushion (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S
The AirTAC MBLCJ63X15-10S is a compact double-acting mini cylinder engineered for high-force operations within confined spaces. It features a rear-mounted stroke adjuster that permits you to trim the 15 mm travel by up to 10 mm, establishing a usable end-position window of 5-15 mm. Driven by a Ø16 mm carbon-steel rod with 20 µm hard-chrome plating, it generates 1558 N of push force and 1457 N of pull force at 0.5 MPa. This specific SKU includes a built-in magnet (-S) for compatibility with AirTAC CMSG reed and DMSG/EMSG electronic sensors, and utilizes a standard PT threaded port.
Diverging from the fixed rubber bumper found on the MBLJ series, this model incorporates a screw-tunable adjustable air cushion at both ends to decelerate heavy loads and shield the end covers from impact shock. The riveted rolling-packed aluminum barrel pairs with a grease-retaining two-way piston seal to maintain consistent lubrication over high-cycle operations. It is critical to note that the rear stopper dictates the travel end-point, while the cushion governs deceleration; neither component functions as a lock to hold a suspended load.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S Technical Specifications
| Model | Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder (adjustable stroke) |
| Bore size | Ø63 mm |
| Nominal stroke | 15 mm |
| Adjustable window | 5–15 mm (trim 10 mm) |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M14×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable air cushion (both ends) |
| Max standard stroke | Up to 500 mm |
The rear stopper sets the end position — it is a travel stop, not a lock. Overall length = A + 2 × stroke + adjustable stroke. MBLJ/MBLCJ mounting is Basic / FA / LB only (no SDB, no back-cover code). Thread options: PT / G / NPT.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a margin.
Model Code: Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S
| MBLCJ | MBLCJ aluminum-barrel adjustable-stroke mini cylinder with adjustable cushion. |
|---|---|
| 63 | Bore size in mm. |
| ×15 | Nominal stroke length in mm. |
| -10 | Adjustable-stroke amount (mm you can trim at the rear). |
| S | Optional built-in magnet for a CMSG/DMSG/EMSG sensor switch. |
Related: MBLJ (adjustable stroke, fixed bumper), MBL (fixed stroke), MBLD (double rod).
Where the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S Is Used
Punch Press Ejection
Provides the 1558 N push force necessary to dislodge heavy stamped metal blanks from tight die cavities, using the 5-15 mm stroke window to time the ejector pin perfectly.
Bottle Capper Sealing
Utilizes the tunable air cushion to gently decelerate the 2181 N force at 0.7 MPa when pressing plastic caps onto beverage lines, preventing bottle fracture during high-speed runs.
PCB Router Clamping
Secures printed circuit boards during routing operations, where the DMSG solid-state sensor detects the rod's end position and the compact riveted barrel fits within dense electronics machinery.
Is the Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S the Right Cylinder?
Selecting the MBLCJ63X15-10S is optimal when maximum short-stroke thrust is required in a compact footprint. If 1558 N of push at 0.5 MPa exceeds your requirement, stepping down to the 50 mm bore yields 981 N of push force. Conversely, as the largest available bore in this series, 63 mm is the ceiling for this mini cylinder family. Compared to the MBLJ variant, this MBLCJ model is preferred for moving heavier masses because its tunable air cushion absorbs kinetic energy that a fixed bumper cannot. For replacements, match the 63 mm bore, 15 mm stroke, 10 mm adjust code, G1/4 port, PT thread, and the -S magnet specification. Mounting is restricted to Basic, FA flange, or LB foot brackets; SDB pivot or back-cover configurations are not available on this chassis.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Adjustable window fits your end position
- ✓ Adjuster is a travel stop, not a lock
- ✓ Magnet (S) for sensors?
- ✓ Side load — add a guide on long strokes
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Set the rear stopper for the end position (a travel stop, not a lock).
- check Avoid side load; add an external guide on long strokes.
- check Mounting: Basic / FA flange / LB foot (no SDB, no back-cover code).
- check Installation by qualified personnel per AirTAC docs.
Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S FAQ
At 0.5 MPa, this double-acting cylinder delivers 1558 N of push force and 1457 N of pull force. At 0.7 MPa, the push force increases to 2181 N. The maximum theoretical force is 318 kgf at 1.0 MPa.
The rear adjuster allows you to trim up to 10 mm from the 15 mm nominal stroke, creating a usable travel window of 5-15 mm. This mechanism acts as a travel stop to set the exact end position, while the separate adjustable air cushion handles end-of-stroke deceleration; neither holds the load in place without live air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Adjustable-Stroke Cylinders
Request a Quote for Airtac MBLCJ Adjustable Mini Cylinder MBLCJ63X15-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.