Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø20mm bore and 100mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ20 mm
- Stroke100 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM8×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S
Trim the forward stop by up to 30 mm on-site without swapping hardware using this stainless-steel, round-body mini cylinder. The MICJ20X100-30S pairs that adjustable extend stroke with a needle-set air cushion at both ends, letting you dial in the exact position while soaking up high-speed shock. Driven by a 1/8" port and an Ø8 rod, it delivers 157 N of push force at 0.5 MPa, yielding a safe working load of roughly 94 N or a 2:1 vertical lift of about 8 kg.
Built to the ISO 6432 mounting interface, it drops into standard mini brackets and clevises. The -S suffix equips the piston with a magnet for CMSG, DMSG, or EMSG sensors. The external screw modifies the extend end only and acts purely as a stop, not a mid-stroke lock. If you need to hold a load on air loss, add an external rod lock or pilot check valve.
Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø20 mm |
| Stroke | 100 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | 185 N |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 20 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S Is Used
Clamp Position Tuning
Dial in the exact 70-100 mm extend reach on machining clamps to accommodate different part thicknesses without re-engineering the fixture.
Soft Stop Diverting
Use the dual air cushions to decelerate the 157 N push force smoothly when actuating lightweight conveyor diverters at high cycle rates.
Vertical Lift Gates
Lift access gates or covers up to 8 kg, relying on the adjustable stop to set the precise open height and prevent over-travel.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S the Right Cylinder?
When sizing, step down to the Ø16 bore for lighter loads (100.5 N push @0.5 MPa) or up to the Ø25 bore for heavier moves (245.3 N push @0.5 MPa). The 30 mm extend adjuster and dual cushions shine in fast set-position applications where you need precise stopping without impact damage. Mount via LB foot, FA flange, or TC trunnion; the SDB pivot block is not offered on this adjustable variant. Position sensing is ready out of the box thanks to the built-in magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S FAQ
This double-acting cylinder uses a 1/8" port and generates 157 N push / 131.9 N pull at 0.5 MPa, and 219.8 N push / 184.7 N pull at 0.7 MPa. Its theoretical maximum force is 32 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 30 mm (usable range 70-100 mm), while the needle-set air cushions at both ends absorb end-of-stroke shock. The -S magnet enables CMSG/DMSG/EMSG sensors. The stop screw is not a mid-stroke lock, and the cylinder will drift on air loss; use an external rod lock for load holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ20X100-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.