Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø25mm bore and 95mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke95 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30
Trim the forward stop by up to 30 mm on site without swapping hardware using this stainless steel round-body mini cylinder. The MICJ25X95-30 delivers a solid 245.3 N push force at 0.5 MPa while twin adjustable air cushions soak up high-speed impact at both ends. Because the bore is Ø25, it drops directly into standard ISO 6432 mini-cylinder mounting brackets and clevises.
The external stop screw sets the extend end position anywhere from 65 to 95 mm, letting you fine-tune the forward stroke on the fly. It yields a safe working load of roughly 147 N, moving about 12.5 kg vertically with a 2:1 safety margin. Note this specific SKU lacks a magnet, so it cannot host CMSG, DMSG or EMSG sensors; specify the -S variant if you require position detection.
Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 95 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 Is Used
Adjustable Stop Clamping
Dial in the exact 65-95 mm forward clamp position on varying part widths while the air cushions absorb the 245.3 N impact at high cycle speeds.
Variable Length Diverting
Extend the rod to custom lengths up to 95 mm to push mixed-size boxes on a conveyor, relying on the 1/8" port pressure for swift retraction.
Soft-Stop Carton Sealing
Use the dual adjustable cushions to gently decelerate the 12.5 kg sealing head before it touches the carton, preventing crush damage.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 the Right Cylinder?
When sizing this 25 mm bore, stepping down to a Ø20 model drops the 0.5 MPa push force to 157 N, whereas moving up to a Ø32 bore increases it to 402 N. Choose this 245.3 N unit when you need moderate thrust combined with on-the-fly extend positioning. The needle cushions tame fast 30-800 mm/s moves, but remember the stop screw only sets the end position—it is not a mid-stroke lock. For holding a suspended load during air loss, fit an external pilot check valve or rod lock. Mount via LB foot, FA flange or TC trunnion (SDB pivot blocks are not offered on adjustable-stroke builds).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30 FAQ
This double-acting cylinder pushes 245.3 N and pulls 206.1 N at 0.5 MPa. At 0.7 MPa it pushes 343.4 N and pulls 288.5 N, with a theoretical maximum of 50 kgf at 1.0 MPa. It features a 1/8" air port and a Ø10 mm piston rod with an M10x1.25 male thread.
An external screw shortens the extend stroke by up to 30 mm on site; retract remains full. Needle-adjustable air cushions at both ends decelerate the piston near stroke ends but do not lock or hold position. Because this SKU lacks a magnet (-S), it cannot accept position sensors, and the piston will drift on air loss unless you add an external rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ25X95-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.