Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 15mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke15 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10
Shave up to 10 mm off the forward end position on site with the AirTAC MICJ32X15-10, a round-body stainless steel mini cylinder built for fast set-and-forget moves. The external stop screw dials in the extend stroke down to a 5 mm minimum, while the adjustable air cushion at both ends soaks up high-speed shock. Driven by a 1/8" port and a 12 mm rod, this double-acting unit pushes with 402.2 N of force at 0.5 MPa.
The stainless barrel and rod shrug off mild corrosion and washdown environments. Because this SKU lacks the -S magnet, it cannot host CMSG, DMSG, or EMSG sensors. Expect a safe working load around 241 N, or enough thrust to vertically lift about 20.5 kg with a 2:1 safety margin. Note that the cushion only decelerates the piston near the stroke end; it is not a mid-stroke lock or brake.
Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 15 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 Is Used
Short-Stroke Clamping
Dial the extend stop down to 5 mm to clamp delicate aluminum housings without crushing them, using 402.2 N of push force.
Gate Diverting
Absorb the shock of high-speed package routing with the dual adjustable air cushions while precisely setting the gate travel.
Product Pushing
Move lightweight cartons off a conveyor belt with a safe working load of 241 N, relying on the stainless rod for washdown durability.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 the Right Cylinder?
If you need less force, stepping down to the Ø25 bore yields 245.3 N of push at 0.5 MPa, whereas moving up to the Ø40 bore provides 628.3 N. The Ø32 hits a sweet spot for moderate loads. Use the 10 mm extend adjuster to nail the forward stop without swapping cylinders, and rely on the needle-set cushion to tame the impact at speeds up to 800 mm/s.
This model uses LB foot, FA flange, or TC trunnion mounts, as the SDB pivot block is not offered on adjustable-stroke variants. Remember that a plain cylinder drifts on air loss—the stop screw sets the end position but will not hold a load mid-stroke. For suspended loads, install an external rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10 FAQ
This double-acting cylinder uses a 1/8" port and delivers a push force of 402.2 N and a pull force of 345.6 N at 0.5 MPa. At 0.7 MPa, push increases to 563 N and pull to 483.8 N. The theoretical maximum force is 82 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm on site, while the needle-set adjustable air cushion at both ends decelerates the piston near the ends to absorb high-speed shock. This SKU has no -S magnet and cannot take sensors. The cushion only decelerates; it is not a brake, so the piston will drift on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X15-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.