Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 160mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke160 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10
Dial in the forward stop without swapping hardware: the AirTAC MICJ32X160-10 uses an external screw to shorten the extend end position by up to 10 mm on site, yielding a usable forward travel of 150-160 mm. Retract remains full, and the adjustable air cushion at both ends soaks up high-speed shock so you set the position and control the impact.
This 32 mm round-body stainless-steel mini cylinder delivers 402.2 N of push force at 0.5 MPa (563 N at 0.7 MPa) and ports via 1/8" thread. It yields a safe working load of roughly 241 N, moving about 20.5 kg vertically with a 2:1 margin. Note this non-magnet SKU cannot take CMSG/DMSG/EMSG sensors; the -S variant is required for position detection.
Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 160 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 Is Used
Press Fit Dial-In
Trim the 10 mm extend stop to seat a 20 kg bearing precisely, letting the dual air cushions absorb the 563 N high-speed impact without slamming.
Heavy Divert Stop
Act as a robust end-stop for larger 32 mm bore conveyor goods, using the adjustable forward position to sync perfectly with the packaging pitch.
Pallet Lift Dampening
Raise loaded pallets vertically and rely on the needle-set cushion to decelerate the 160 mm stroke smoothly, preventing shock damage to the stainless rod.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 the Right Cylinder?
When sizing this 402.2 N @0.5 MPa unit, step down to a 25 mm bore (245.3 N push) if your load is lighter, or up to a 40 mm bore (628.3 N push) for heavier moves. The 10 mm extend trim shines in fast set-position routines where you must nudge the endpoint precisely without re-engineering the fixture.
Mount via LB foot, FA flange or TC trunnion (SDB pivot-block is unavailable on this adjustable variant). The stop screw and cushion only decelerate near stroke end; they do not lock the piston. If you need to hold a load on air loss, add an external rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10 FAQ
This 32 mm bore cylinder ports via 1/8" thread and delivers 402.2 N push / 345.6 N pull at 0.5 MPa, 563 N push / 483.8 N pull at 0.7 MPa, with a theoretical max of 82 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm (retract is unaffected), while needle valves tune the air cushion at both ends to absorb high-speed shock. The cylinder does not hold position on air loss; use an external rod lock for that. This non-S SKU lacks a magnet, so it cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X160-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.