Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 170mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke170 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S
Dial in a precise forward stop without swapping hardware using this stainless steel round-body mini cylinder. The external screw shortens the extend stroke by up to 10 mm on site, giving a usable forward range of 160 to 170 mm, while the needle-set air cushion at both ends soaks up high-speed shock. As a double-acting actuator, it delivers substantial force with a 1/8 inch air port and an M10x1.25 male rod thread.
At 0.5 MPa it pushes 402.2 N and pulls 345.6 N, yielding a safe working load of about 241 N or a vertical lift of roughly 20.5 kg with a 2:1 margin. The riveted stainless barrel and rod resist mild corrosion and washdown. Because this is an -S model, the built-in piston magnet supports CMSG, DMSG and EMSG switches for position sensing.
Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 170 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S Is Used
Sorter Diverter Stop
Halts fast-moving packages on a belt by tuning the 10 mm extend stop to the exact lane edge, letting the dual air cushion absorb the 402.2 N push impact smoothly.
Carton Flap Folder
Swings heavy cardboard flaps into position at speed; the needle cushion decelerates the 20.5 kg vertical lift force before contact to prevent crushing the box.
Press Pin Insertion
Drives a pin to a precise 165 mm depth using the external stop screw, relying on the 563 N push at 0.7 MPa to seat the component without rebound.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S the Right Cylinder?
For lighter duty, the Ø25 bore provides 245.3 N of push force at 0.5 MPa, whereas stepping up to the Ø40 bore yields 628.3 N. This Ø32 model fits neatly in the middle, delivering 563 N of push at 0.7 MPa. The adjustable 10 mm extend stop plus dual air cushions excel in fast set-position moves where you must tune the forward impact without changing the entire actuator.
Remember that the stop screw sets the end position but is not a mid-stroke lock; the cushion only decelerates near the stroke end. If you need to hold a load on air loss, install an external rod lock or pilot check valve. Mount using LB foot, FA flange or TC trunnion brackets, as the SDB pivot block is not offered on this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S FAQ
This double-acting cylinder uses a 1/8 inch air port. At 0.5 MPa it pushes 402.2 N and pulls 345.6 N. At 0.7 MPa it pushes 563 N and pulls 483.8 N. The theoretical maximum force is 82 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm, setting the forward end position without affecting the full retract. Needle valves adjust the air cushion at both ends to decelerate the piston near stroke ends. The -S magnet enables CMSG, DMSG and EMSG sensors. It does not hold position on air loss; use an external rod lock for that.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X170-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.