Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 175mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke175 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S
Dial in a precise forward stop on-site with the AirTAC MICJ32X175-10S, a stainless round-body mini cylinder featuring an external screw that shortens the extend stroke by up to 10 mm. The usable extend range is 165-175 mm, letting you trim the forward end position without swapping hardware. A needle-set variable air cushion at both ends soaks up high-speed shock, ensuring smooth deceleration near the stroke ends.
Built with a 32 mm bore and a 12 mm rod, this double-acting actuator pushes with 402.2 N and pulls with 345.6 N at 0.5 MPa. The stainless steel barrel and rod resist mild corrosion and washdown environments. Because this is a -S model, the built-in piston magnet supports CMSG, DMSG, and EMSG sensors for position detection. It operates at speeds from 30 to 800 mm/s and uses a 1/8" port.
Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S Is Used
Diverting Gate Adjustment
Trimming the extend stroke by up to 10 mm lets operators fine-tune a conveyor diverting gate position on-site while the dual air cushions absorb the impact of high-speed package routing.
Carton Sealing Press
Provides 402.2 N of push force at 0.5 MPa to hold carton flaps, with the needle-set cushion preventing hard slamming at the end of the 175 mm stroke.
Vertical Lift Stop
Lifts roughly 20.5 kg of inventory vertically using a 2:1 safety margin, with the external stop screw allowing precise top-position tuning without changing the cylinder body.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S the Right Cylinder?
For lighter loads, the Ø25 bore provides 245.3 N of push force at 0.5 MPa, while the larger Ø40 bore steps up to 628.3 N if you need more thrust. The Ø32 bore hits a sweet spot, yielding a safe working load of roughly 241 N and a vertical lift capacity of about 20.5 kg with a 2:1 margin. The 10 mm extend adjuster is ideal for fast set-position moves where you need to dial in a precise endpoint without mechanical rework.
Mounting options include LB foot, FA flange, and TC trunnion, plus CA, U, R, or CM back covers, but the SDB pivot-block is not available on this adjustable variant. Remember that the stop screw and air cushion only decelerate the piston near the end of travel; they do not function as a mid-stroke lock. If your application must hold a load on air loss, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S FAQ
This double-acting cylinder uses a 1/8" port and generates 402.2 N of push force and 345.6 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 563 N and the pull force is 483.8 N. The theoretical maximum force is 82 kgf at 1.0 MPa.
The external screw shortens the extend stroke by up to 10 mm (usable range 165-175 mm), setting the forward end position without affecting the full retract. The needle-set variable air cushion decelerates the piston near both stroke ends to absorb high-speed shock. The -S suffix indicates a built-in piston magnet for use with CMSG, DMSG, and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X175-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.