Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 175mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke175 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75
Trim the forward stop by up to 75 mm on site without swapping hardware using the AirTAC MICJ32X175-75. This 32 mm bore, double-acting round-body stainless mini cylinder pairs that external extend adjuster with a needle-set variable air cushion at both ends to soak up high-speed shock. The stainless barrel and rod resist mild corrosion and washdown, and the 1/8" port feeds a robust 402.2 N push force at 0.5 MPa.
Because the stop screw only shortens the extend end (usable forward range 100-175 mm), you set the exact impact point while the needle controls deceleration near the ends. This non-ISO-6432 size delivers a computed safe working load of roughly 241 N, translating to a vertical lift of about 20.5 kg with a 2:1 margin. Note this SKU lacks a magnet, so it cannot take CMSG/DMSG/EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 Is Used
Press Fit Tuning
Dial in the 100-175 mm extend stop to press bearings precisely, leaning on the 402.2 N push force while the air cushion softens the final impact.
Heavy Diverter
Shift heavier goods on a belt using the 20.5 kg vertical lift capacity, adjusting the reach on-site to match varying lane widths.
Carton Stopper
Halt large packaging at a packing station; the stainless build handles washdown, and the needle cushion absorbs the 800 mm/s shock.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 the Right Cylinder?
When sizing, step down to the 25 mm bore for lighter 245.3 N push tasks, or move up to the 40 mm bore if you need 628.3 N. The 32 mm bore hits a strong middle ground at 402.2 N push and 345.6 N pull at 0.5 MPa. The adjustable stop and dual cushions shine in fast set-position moves where you must tune the forward landing precisely.
Remember the stop screw sets the end position but is not a mid-stroke lock; if air drops, the piston drifts, so add an external rod lock or pilot check valve to hold a suspended load. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is unavailable here), and select the -S variant if you need position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75 FAQ
It features a 1/8" port and delivers 402.2 N push / 345.6 N pull at 0.5 MPa, 563 N push / 483.8 N pull at 0.7 MPa, with a theoretical max of 82 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 75 mm (retract stays full), while a needle-set variable air cushion at both ends decelerates the piston near stroke end. It is not a mid-stroke lock; the piston drifts on air loss, so use an external rod lock for holding. This non-magnet SKU cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X175-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.