Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 350mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke350 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S
Trim the forward stop by up to 40 mm on site without swapping hardware using this AirTAC MICJ32X350-40S round-body mini cylinder. The external screw shortens the extend end position (usable range 310-350 mm), while a needle-set variable air cushion at both ends soaks up high-speed shock. As a double-acting stainless-steel unit, it provides 402.2 N of push force at 0.5 MPa, yielding a safe working load of roughly 241 N or a 20.5 kg vertical lift with a 2:1 margin.
Built with a Ø32 mm bore, a 1/8" air port, and an M10x1.25 male rod thread, this riveted construction resists mild corrosion and washdown environments. The -S suffix denotes a built-in piston magnet for CMSG, DMSG, or EMSG sensors. Note that Ø32 is a non-ISO-6432 size, and the stop screw only sets the end position—it is not a mid-stroke lock.
Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 350 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×350 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S Is Used
Press Fit Tuning
Dial in the exact 310-350 mm extend reach for seating bearings, using the 402.2 N push force and needle cushions to prevent impact bounce at 800 mm/s.
High-Speed Diverting
Rely on the 20.5 kg vertical lift capacity to divert heavier cartons, trimming the forward stop by 40 mm to match varying package widths perfectly.
Washdown Sealing
Leverage the stainless steel barrel and rod for mildly corrosive packaging lines, setting the extend position without exposing the mechanism to contaminants.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S the Right Cylinder?
When sizing this 32 mm bore, stepping down to a 25 mm model drops the 0.5 MPa push force to 245.3 N, whereas moving up to a 40 mm bore increases it to 628.3 N. Choose this 32 mm variant when you need about 241 N of safe working force combined with on-the-fly extend trimming for fast set-position moves.
The dual adjustable cushions shine in high-speed cycling, but remember the cylinder will drift on air loss—the cushion only decelerates near the stroke end and never acts as a brake. For load holding, install an external rod lock or pilot check valve. Mount via LB foot, FA flange, or TC trunnion (SDB is not offered), and use the -S magnet to fit reed or electronic sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S FAQ
This double-acting cylinder delivers a push of 402.2 N and pull of 345.6 N at 0.5 MPa, and a push of 563 N / pull of 483.8 N at 0.7 MPa. The theoretical max force is 82 kgf at 1.0 MPa. It uses a 1/8" air port and a Ø12 mm piston rod.
An external screw shortens the extend stroke by up to 40 mm on site, giving a usable forward range of 310-350 mm (retract remains full). The needle-set variable air cushions at both ends absorb high-speed shock. The -S suffix enables CMSG/DMSG/EMSG sensors, and the stainless build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X350-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.