Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40
The AirTAC Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 is a genuine double acting, adjustable stroke + cushion round-body mini air cylinder with a Ø32mm bore and 60mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40
Dial in the forward stop without swapping cylinders: the MICJ32X60-40 uses an external screw to shorten the extend end by up to 40 mm on site, giving a usable forward range of 20-60 mm. Retract remains full, and a needle-set variable air cushion at both ends soaks up high-speed shock so you control both the position and the impact.
This round-body stainless steel mini cylinder delivers 402.2 N of push force at 0.5 MPa through a 1/8" port, making it a robust choice for mid-weight automation. The stainless barrel and rod resist mild corrosion and washdown. Note this non-magnet SKU cannot take a sensor; the -S variant is required for CMSG/DMSG/EMSG switches. With a safe working load around 241 N, it lifts about 20.5 kg vertically with a 2:1 margin.
Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 |
|---|---|
| Series | MICJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 60 mm |
| Acting type | Double acting, adjustable stroke + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40
| MICJ | round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 Is Used
Press Fit Dialing
Set the exact 35 mm extend stop for pressing small bearings, letting the dual air cushions absorb the 402.2 N impact without slamming.
Diverter Gate Control
Trim the extend stroke to 45 mm to deflect packages on a line, using the adjustable end position to match varying belt widths perfectly.
Carton Flap Tucking
Deliver a precise tuck against cartons, tuning the needle cushion to stop the 32 mm bore rod smoothly before it dents the cardboard.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 the Right Cylinder?
Stepping down, the smaller Ø25 bore provides 245.3 N push @0.5 MPa, which is likely too weak if you need the 402.2 N thrust this Ø32 provides; stepping up to Ø40 yields 628.3 N for heavier loads. Choose this adjustable-stroke model when you need fast set-position moves and want to tune out end-of-stroke shock without adding external shock absorbers.
The stop screw sets the end position but is not a mid-stroke lock, and the air cushion only decelerates near the stroke end. If the application must hold a load on air loss, add an external rod lock or pilot check valve. Mount using LB foot, FA flange or TC trunnion (SDB pivot-block is not available), and select the -S version if you need position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40 FAQ
This double-acting cylinder has a 1/8" port and an M10x1.25 male rod thread. It delivers 402.2 N push and 345.6 N pull at 0.5 MPa, 563 N push and 483.8 N pull at 0.7 MPa, with a theoretical max of 82 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 40 mm (retract is full), while needle valves adjust the air cushion at both ends to decelerate high-speed moves. The cushion is not a brake, and the cylinder drifts on air loss; use a pilot check valve to hold a load. This non-magnet SKU cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ32X60-40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.