Airtac MIJ Adjustable Cylinder MIJ10X20-10S
The AirTAC Airtac MIJ Adjustable Cylinder MIJ10X20-10S is a genuine double acting, adjustable stroke round-body mini air cylinder with a Ø10mm bore and 20mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ10 mm
- Stroke20 mm
- Port sizeM5×0.8
- Acting typeDouble acting, adjustable stroke
- Rod threadM4×0.7
- CushionFixed TPU bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIJ Adjustable Cylinder MIJ10X20-10S
Dial in your forward end position on-site with the AirTAC MIJ10X20-10S, a round-body stainless steel mini cylinder featuring a 10 mm extend-stroke adjustment window. An external stop screw lets you trim the forward travel from its 20 mm nominal maximum down to 10 mm, absorbing setup tolerances without swapping parts. The retract stroke remains full length. Built with a riveted stainless barrel and rod, it handles mild washdown environments effortlessly.
Driven by filtered air at 0.15-1.0 MPa, this double-acting Ø10 mm bore generates 39.3 N of push force at 0.5 MPa. That translates to a safe working load of roughly 24 N, or a vertical lift capacity of about 2 kg with a 2:1 safety margin. The M5x0.8 port and M4x0.7 male rod thread simplify pneumatic and mechanical connections. Because this SKU includes the -S magnet, it is fully ready for CMSG, DMSG, or EMSG position sensing.
Airtac MIJ Adjustable Cylinder MIJ10X20-10S Technical Specifications
| Model | Airtac MIJ Adjustable Cylinder MIJ10X20-10S |
|---|---|
| Series | MIJ ISO 6432 mini cylinder |
| Bore size | Ø10 mm |
| Stroke | 20 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39 N | 33 N |
| 0.7 MPa | 55 N | 46 N |
| Max (@1.0 MPa) | 8 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIJ Adjustable Cylinder MIJ10X20-10S
| MIJ | ISO 6432 round-body mini cylinder (adjustable-stroke). |
|---|---|
| 10 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIJ Adjustable Cylinder MIJ10X20-10S Is Used
Small Part Ejection
Uses the 39.3 N push force to knock lightweight plastic parts from a mold, dialing the 10 mm stop screw to match varying part thicknesses without retooling.
Sorter Diverter
Snaps small packages on a conveyor using a 2 kg vertical lift capacity, adjusting the forward stroke on-site to accommodate different box widths.
Lab Sample Routing
Pushes test tubes into a carousel with precise 10-20 mm extend travel, relying on the stainless build and -S magnet for washdown and position confirmation.
Is the Airtac MIJ Adjustable Cylinder MIJ10X20-10S the Right Cylinder?
When sizing this actuator, compare its 39.3 N push @0.5 MPa against the smaller Ø8 bore (25.1 N) or the larger Ø16 bore (100.5 N) to ensure adequate force. The 10 mm adjustment screw is ideal for fine-tuning the extend end during changeovers, letting one part number cover several slightly different forward stops. Mounting follows the ISO 6432 mini-cylinder interface, accepting standard LB foot, FA flange, or TC trunnion brackets, but the SDB pivot block is not available on this adjustable variant.
Keep in mind that the stop screw only sets the end position; it is not a mid-stroke lock. If air pressure drops, the piston will drift, as the fixed TPU bumper pads only decelerate the stroke end rather than holding the load. For vertical loads requiring position holding on air loss, install an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIJ Adjustable Cylinder MIJ10X20-10S FAQ
This double-acting cylinder uses an M5x0.8 port and delivers 39.3 N push / 33 N pull at 0.5 MPa, and 55 N push / 46.1 N pull at 0.7 MPa. The theoretical maximum force is 8 kgf at 1.0 MPa.
The external stop screw shortens the extend stroke by up to 10 mm (usable forward travel 10-20 mm), while retract remains full. The -S suffix means a piston magnet is built-in for CMSG/DMSG/EMSG sensors. Fixed TPU bumpers decelerate the ends.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIJ Adjustable Cylinder MIJ10X20-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.